铝合金

The digital analysis of the three standard samples of the Al-based alloy with different content of Cu, and the probe into the quantitative analysis that employs the spectrums of Cu 510.55 nm and Fe 510.75 nm as the analysis spectrum and comparison spectrum, indicate the positive relationship between the content of copper and the intensity ratio of the analysis and comparison of spectrum.

对3种不同Cu元素含量的铝合金标准样品进行数字化分析测定，探索选用Cu 510.55nm谱线和Fe 510.75nm谱线分别作为分析谱线和比较谱线进行定量测定的方法，数据显示分析谱线和比较谱线的强度比值与Cu元素含量呈正比关系。

The digital analysis of the six standard samples of the Al-based alloy with different content of Cd, and the probe into the quantitative analysis that employs the spectrums of Cd 508.5 nm as the analysis spectrum, Cu510. 55 nm and Fe510.75 nm as comparison spectrum separately, indicate the positive relationship between the content of cadmium and the intensity ratio of the analysis and comparison of spectrum.

对6种不同Cd元素含量的铝合金标准样品进行了数字化分析测定，探索了选用Cd 508.58nm谱线作为分析谱线，分别选用Cu510.55nm和Fe510.75nm谱线作为比较谱线进行定量测定的方法，数据显示分析谱线和比较谱线的强度比值与Cd元素含量成正比关系。

The lauan wood is used as a template to prepare Al/C and Al/ composites. Porous carbon is first pyrolyzed from the wood template. The final composites having wood structure are obtained by injecting aluminum alloy and silicone resin into the porous carbon. The microstructures, thermal expansions, and thermal conductivity of these products are analyzed by the scanning microscope, dilatometer, and conductometer. The model of thermal conduction is established.

该文以柳桉木材为模板，先将其转变为多孔碳，再通过铝合金和硅树脂的浸渍，制备了具有木材结构的Al/C、Al/两种铝基复合材料，并通过扫扫电镜、热膨胀仪和导热仅对复合材料的微观结构、热膨胀性能及导热性能进行了研究，建立了导热模型。

According to conformal mapping theory of complex function, forward and reverse solution procedure of Schwarz-Christoffel transformation is analyzed.

论文摘要：针对复杂铝合金壁板导流模挤压过程中出现的挤压力大、变形不均等缺陷，采用流函数理论建立扁挤压筒型腔到型材出口之间过渡曲面的边界条件。

Finally, the constitutive relation of this alloy aluminum was constructed based on the experimental results.

最后，根据实验结果确定了该铝合金材料的本构关系。

This nugget growth mode depends on the characteristic of distribution of contact force and current density during RSW process.

这与锥台形电极点焊初始熔核为一熔化环不同，这是由铝合金点焊过程中接触压力和电流密度分布特点所决定的。

The influence of the strontium content and holding time on the cooling curve of ZL104 aluminum alloy was studied using a self-regulating thermal analysis system.

利用自主开发的铝合金热分析系统，研究了Sr加入量、变质后保温时间对ZL104合金冷却曲线的影响，建立了变质等级与变质前后共晶温度的降低值△TEG之间的对应关系。

The influence of the strontium content and holding time on the cooling curve of ZL104 aluminum alloy was studied using a self-regulating thermal analysis system.The relationship of modification level and △TEG(the eutectic temperature difference between modified and unmodified alloy) was established.

利用自主开发的铝合金热分析系统，研究了Sr加入量、变质后保温时间对ZL104合金冷却曲线的影响，建立了变质等级与变质前后共晶温度的降低值△TEG之间的对应关系。

The pure copperplate was butt jointed with the aluminium alloy plate of 7075,5086,5356 and 2024 by autogeneous welding process of TIG.

电弧自体接合的板状纯铜与铝合金7075、5086、5356和2024接合，经X-Ray测量结果显示，在对接焊道附近有拉伸残留应力存在。

Selects PA66 which Italy imports to put on the strip, with the trundle connection craft and the aluminum alloy union is a whole, two kind of material qualities rise the coefficient to be close hotly, union science.

选用意大利进口的 PA66穿条，用滚压连接工艺和铝合金结合为一个整体，两种材质热涨系数接近，结合科学。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。