铝化

When the above-mentioned anions were added into the solution, the breakdown potential and negative difference effect of aluminum were found to change.

1前盲纯铝在PH二4～9的水溶液中，由于与溶液中的氧有强烈的亲合力，生成保护性较高的饨化膜，抑制了铝的自腐蚀。

Over the AlPO〓, the deamination and dealkylation of diethylmine and triethylmine produced ethylene selectivily. Over AlPONs of acid-base bifunctional catalysts the ethylnitrol formed selectivily.

二乙胺、三乙胺在酸性的磷酸铝上选择性的脱烷基/脱氨生成乙烯，在酸碱两性的氮化磷酸铝上选择性脱烷基/脱氢生成乙腈。

The process of producing low-carbon aluminium killed steel using new deoxidant in the steelmaking plant of Baotou Iron and Steel Co was introduced.

介绍了包钢炼钢厂小方坯连铸机开发生产新钢种以及转炉采用新型复合脱氧剂生产低碳铝镇静钢的工艺路线，采用新型工艺路线及脱氧剂脱氧合金化后，Al收得率平均提高1倍以上，钢中氧的质量分数控制在10×10-6~50×10-6，低碳铝镇静钢的炼成率达99%以上，铸坯质量合格

Aluminium Fluoride, molecular formula: AlF3, is mainly used to adjust the molecular ratio in aluminium electrobath, lower the smelting point of media and increase the conductivity of electrolyte. It is also used as the inhibitor in alcoholic fermen tation, the flux of vitreous enamel around the ceramics and the flux of the non-iron metal etc.

氟化铝，分子式：AlF3，白色粉状固体，主要用于调整铝电解槽电解质的分子比，降低熔点和提高电解质的导电率，还用于生产酒精时作发酵的抑止剂，陶瓷外层釉彩的助熔剂，非铁金属的熔剂等。

we use magnetron sputtering to deposit Al-AlN particle film as SED's electron-emitter. The Cr-Cu-Cr electrode was prepared by electron beam vaporize deposition. The voltage used to electroform the cracks are periodic trigonal wave and the breadth of the voltage are increasing gradually.

文章中采用铝-氮化铝薄膜材料作为SED器件的电子发射层，采用磁控溅射的方法镀电子发射层，采用电子束蒸发的方法镀铬-铜-铬材料作为电极；电形成过程中采用电压幅值恒定、周期性重复的脉冲和电压幅值渐增的电压脉冲作为电极电压。

Such derivatives are prepared by reacting a kaolin group mineral with a reagent, such as, an alkali metal halide or an ammonium halide which converts the majority of the octahedrally coordinated aluminum in the kaolin group mineral to tetrahedrally coordinated aluminum.

这种衍生物是通过将高岭族矿物与一种试剂，例如一种碱金属卤化物或一种卤化铵进行反应，从而将高岭族矿物中的大部分六配位铝转化为四配位铝而制备的。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area;2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support;3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier;4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling;5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene PolymerizationIn this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that:1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS;2.co-mlling time had no obvious effect on the texture of support after 12 hours;3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现；3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布；4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒；5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明：1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致；2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响；3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area; 2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support; 3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier; 4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling; 5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene Polymerization In this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that: 1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS; 2.co-mlling time had no obvious effect on the texture of support after 12 hours; 3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现； 3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布； 4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒； 5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明： 1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致； 2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响； 3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Through comparing and analyzing the metallurgical effects, proper addition quantity of the modifier was 80 kg per heat. The experiment results showed that the modifier smelted the slag fast and reduced the oxidizability of the top-slag rapidly. Comparing with the original process, the average content of aluminum in the steel was increased by 0.06%, desulphurization ratio was increased by 89.25% and TFe was reduced by 0.6%, then stabilizing the production of aluminum containing steel.

试验中用改质剂代替原工艺中的精炼剂（Q235C钢种），通过对改质剂不同加入量的冶金效果进行对比分析，确定的改质剂加入量为每炉80 kg，试验表明，改质剂化渣快，能迅速降低顶渣的氧化性，与原工艺相比，钢中平均铝含量提高0.06%，脱硫率提高89.25%，渣中全铁降低0.6%，稳定了含铝钢的生产。

In acid pulp, the depressing abilities of reagents on diaspore are in the order of hydroxamic acid starch＞dialdehyde starch＞carboxymethyl starch＞cationic starch＞primary starch. In addition, hydroxamic acid starch and carboxymethyl starch can activate kaolinite without influence on the recoveries of pyrophyllite and illite, so the two reagents have great potential and prospect to be the depressant of diaspore and the activator of kaolinite in bauxite reverse flotation.(3) By oximation of the copolymer of acrylamide and methyl acrylate, hydroxamic acid polyacrylamide is synthesized.

3对丙烯酰胺和丙烯酸甲酯的共聚物肟化制得氧肟酸聚丙烯酰胺，将它同非离子聚丙烯酰胺、阴离子聚丙烯酰胺、阳离子聚丙烯酰胺和两性聚丙烯酰胺分别应用于四种矿物的单矿物浮选试验，结果显示，改性聚丙烯酰胺对一水硬铝石、高岭石和伊利石均具有活化作用，其中，药剂对高岭石的活化最强，使它的回收率在整个pH值范围达到80％左右，在一定pH条件下超过一水硬铝石的回收率，解决了高岭石难浮选的问题。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。