钼

Effects of boron and molybdenum fertilizer on plant growth and cell ultra-microscopic structure of Chamaecrista rotundifolia were studied by pot test.

通过盆栽试验探讨了红壤施用不同浓度的硼、钼微肥对圆叶决明植株生长和叶肉细胞超显微结构的影响。

Preparation of the cathode includes:shaping under the press of 40Mpa, sintering at 550℃for 1 hour and at 900℃for 8 hours and threading with molybdenum bar; Considering the literatures we choose CaCl2 as salt for preparation titanium. Pretreatment of salt is for 1 hour at 100℃and for 2 hours at 300℃. Partial pressure of oxygen which need lower than 5.11×10-7Pa to reduct titanium oxides and hygroscopic property of salt need a sealed equipment to electrolyse. And finally successfully designed a satisfied one and the results show that the equipment can be satisfied the requirment of the experiment. Flow of the inert gas is 1.5L/min, the voltage is 2.8 V, temperature is 850℃and time is 2 hours during pre-electrolysis. Flow of the inert gas is 0.2L/min, the voltage is 3.1 V, temperature is 900℃and time changes with the mass of TiO2 during electrolysis, namely the greater need the longer time; To eliminate influence of salt and other impurities, the products need to wash with distilled water and dilute chlorhydric acid , then wash with dilute hydrochloric acid under supersonic wave assistant. Finally, electrometical properties of the electrolysis of TiO2 is researched by cyclic voltammetry and chronoamperometry, and results show that there are two main reodox steps, namely from TiO2 to TiO and from TiO to Ti.

阴极制备主要包括40MPa压力下模压成型、两段式烧结(1小时内升至550℃保温1小时，再1小时升温至900℃保温8小时)及烧结后TiO2块打孔用钼棒串接三个主要环节；实验中选用CaCl2作为电解熔盐，并对其进行预处理(100℃，保温1小时； 300℃，保温2小时)；经热力学计算，还原钛氧化物的氧分压至少要低于5.11×10-7Pa，结合电解过程中所用熔盐CaCl2有极强的吸水性的特点，电解装置应有较高的密封性，自行设计了一套密封性可靠的电解装置，便于实验过程中熔盐预处理和氧分压的控制；通过干燥处理预电解过程中Ar流量大约为1.5L/min、电压为2.8 V、温度为850℃、时间为2小时，电解过程中Ar流量大约为0.2L/min、电压为3.1V、温度为900℃，实验结果表明电解时间与TiO2质量密切相关，质量越大需要电解的时间越长；通过自来水冲洗—稀盐酸浸泡、洗涤—在超声波辅助作用下稀盐酸洗涤，可减少熔盐及其它杂质对电解产物检测结果的影响；最后，通过循环伏安法、计时电流法对电解机理的研究，确定电解还原TiO2制备金属钛主要经历了TiO2-TiO-Ti的过程。

The results show that the technical parameters and the concentration of sodium molybdate have obvious effect on the composition of the alloy. The crystal grain size is from 6.2 to 12.7 nm and changes with current density, temperature and the pH value of the electrolyte.The crystalline growth of the alloy accords with the model of three-dimensional growth. The surface morphology is mainly determined by the rate competitions between the growing direction of vertical surface and the expanding direction along the surface towards circumambient. The results of the X-ray data show the presence of the multiphase containing solid solution and intermetallic compound in the deposits. The deposit phases alter from the FeNi and FeMo solid solution to the FeNi and MoNi4structure at 3 A/dm2. The deposits internal stress increases linearly with the decrease of the grain size. The lattice parameter of the deposits are slightly distorted

结果表明：工艺条件和钼酸钠浓度对合金组成的影响较大；所得合金晶粒尺寸为6.2~12.7 nm，并随电流密度、温度和电镀液的pH值的改变而变化；合金的晶体生长符合晶核三维生长模型，镀层表面形貌由平行和垂直于基体的生长速度的相对大小决定；镀层物相为固溶体和金属间化合物的多相结构，当电流密度为3 A/dm2时，镀层物相由FeNi和FeMo固溶相转化为FeNi和

Alloy of polyethylene of element of the methodological freeboard that make, titanium and sample of alloy of cobaltic chromic molybdenum, FITC of classics of cuticular grape coccus labels, the cuticular grape coccus that after sample of artificial and articulatory material is disinfected, vaccinal FITC labels, sample surface cent is slick surface and rough surface, every groups each 6 sample, brood the 24 orifice plate that contain bacterium and sample below 37 ℃ after Yo 30min, with fluorescent microscope observation, sample uses observation of scanning report lens.

方法制作超高分子聚乙烯、钛合金和钴铬钼合金试样，表皮葡萄球菌经FITC标记，人工关节材料试样消毒后接种FITC标记的表皮葡萄球菌，试样表面分为光滑表面和粗糙表面，每组各6个试样，将含有细菌和试样的24孔板在37℃下孵育30min后，用荧光显微镜观察，试样用扫描电镜观察。

Among those processes, demethylation is more favorable than the hydroxylation, but the hydroxylation results in the largest number of intermediates.

通过采用优化的钼篮比色法测定降解产物PO_4~(3-)研究了甲胺磷在介孔纳米TiO_2悬浮液中的光催化降解。

An ordered Si-C alloy was observed in the products resulting from thermal reduction of molybdenum disilicide heating rods.

在硅钼棒的热解产物中发现了一种高碳浓度的Si_(1-x)C_x单晶材料。

The main radiation cavity of the furnace consists of a high-purity alumina tube 25cm long x7cmi.d., heated by molybdenum disilicide elements.

加热炉里的主要辐射腔是一条内直径7公分，长25公分的高纯度氧化铝管，由二硅化钼元素加热。

The main radiation cavity of the furnace consists of a high-purity alumina tube 25cm long x7cmi.d., heated by Molybdenum rod disilicide elements.

加热炉里的主要辐射腔是一条内直径7公分，长25公分的高纯度氧化铝管，由二硅化钼元素加热。

Molybdenum disilicide ; abrasive wear ; wear mechanism

二硅化钼；磨粒磨损；磨损机理

Barry Trost and Kalindi Dogra at Stanford University were able to avoid that problem and other pitfalls in building the chemical by using a molybdenum catalyst.

斯坦福大学研究人员巴里·特罗斯特和卡林蒂·多格拉通过采用钼催化剂制造四氢大麻酚，可以避免上述问题。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐