钢状
- 与 钢状 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Such specimens could not be remedied by the usual quench andtemper treatment, and re-solution treatment at high temperatures (980-1050℃)followed by rapid cooling to room temperature was necessary to modify the sizeand distribution of the boron-containing phase, with the consequence of improvingproperties and eliminating the shell-shaped fracture.
对于出现&壳层状硼脆断口&的50B钢,正常的调质处理不能恢复其性能。但在980—1050℃重新固溶处理并以较快速率冷却到室温则可以改变硼相的析出形态,并改变相应的断口形态,相应地性能也恢复或有所提高。
-
This paper introduced X70 and X80 HRC with heavy thickness which were designed by low carbon, high niobium acicular ferrite microstructure , and developed on medium thickness slab continuous casting production line in Ansteel.
介绍了鞍钢股份有限公司采用低碳高铌针状铁素体组织设计、在中等厚度连铸坯连铸连轧生产线上研制开发特厚规格X70和X80级管线钢热轧卷板的情况。
-
Moreover, the electromagnetic flux density and meniscus height increase in the form of chequerboard with increasing of slit number. The numerical results can exactly illuminate some experimental phenomena, and enrich the theoretical foundation of soft-contact continuous casting technology. In practice, a softcontact mold with slit number of 16 or 24 is recommended, the suggested frequency is around 20kHz, and the slit width is about 1mm.
结果表明:钢液对结晶器内的电磁场分布有很大影响;发现了磁感应强度和弯月面高度随电源频率增加而增大的频率范围、磁感应强度和弯月面高度随切缝数目增加呈&锯齿状&增大的规律;研究结果合理地解释了一些实验现象,完善了软接触结晶器电磁连铸技术的理论基础;建议在实际应用中采用分瓣数为16或24分瓣数的结晶器,电源频率应控制在20kHz左右,切缝宽度应控制在1mm左右。
-
The results showed that the micro-character of the transverse cracks embedded in the S355 steel plate was severe band structure.
研究发现钢中存在严重的带状组织,裂纹附近有密集的点状内氧化,还有大量的包状晶网络。
- 推荐网络例句
-
However, as the name(read-only memory)implies, CD disks cannot be written onorchanged in any way.
然而,正如其名字所指出的那样,CD盘不能写,也不能用任何方式改变其内容。
-
Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.
镀锌钢托盘多用于出口,替代木托盘,免薰蒸,符合欧盟、北美各国对出口货物包装材料的法令要求;喷涂钢托盘适用于重载上货架之用,托盘表面根据需要制作成平板状、波纹状及间隔形式,满足不同的使用要求。
-
A single payment file can be uploaded from an ERP system to effect all pan-China RMB payments and overseas payments in all currencies.
付款指令文件可从您的 ERP 系统上传到我们的电子银行系统来只是国内及对海外各种币种付款。