量热

In this paper, the dynamic compressing experiments for the matrix material of the tungsten alloys which have been three different deforming(0%、 32.6%、 44.6%) processed have been performed by the experimental technology of separated Hopkinson pressure bar and many accurate datum have been obtained. Also the three materials have been compared with each other and analyzed. The results show that the optimized values are in a certain range to optimize the materials by changing their deforming technology. The parameters of constitutive model of Johnson-Cook have been fitted based on the datum. Then proceed to the next step, adiabatic shear band of these three matrix materials has been analyzed with finite element method. The result shows that the relations between stress and strain are different because of the differences of technical process of the three materials, but they are in great commonness in the material experiment and in great coherence in the distribution of time and space, which can been seen from the space distributing figures of plastic strain.

利用分离式Hopkinson压杆实验技术对三种不同变形量(0%、32.6%、44.6%)钨合金基体材料进行动态压缩实验，取得大量精确的数据，对比分析三种材料，结果表明通过改变变形量对材料进行优化，其变形量的优化值是有一定范围的；本论文拟合、确定了钨合金基体材料Johnson-Cook本构模型参数并对三种基体材料绝热剪切带进行有限元分析，结果表明三种材料由于工艺流程的不同，应力应变关系也不尽相同，但从塑性应变的空间分布图上体现了材料很大的共性和时间以及空间分布的一致性。

Some parameters such as Indoor radiation heat transfer, convective heat transfer, MRT, OT, radiation heat transfer coefficient, convective heat transfer coefficient, and PMV-PPD were calculated under a steady condition. From the result, we can conclude, when operation under the combination system and worst-case test, if floor temperature is about 21℃, supply air temperature is 21℃, air velocity is 1m/s, the equlvalent coefficient of heat transfer between floor temperature and OT is 13.6w/m2k, where 5.68w/m2k is equlvalent coefficient of radiant heat transfer, 9.48w/m2k is convective heat transfer coefficient. And when air velocity is higher, supply air temperature is lower, the radiant heat transfer between floor and others is lower. In the whole experiment, the floor temperature was keeping above the indoor air dew point, and condensation was not appeared.

通过分析计算，在复合式系统运行中，最不利室外环境下，当地面温度维持在21℃左右，送风温度21℃，送风风速1m/s，此时地板对作用温度的当量综合换热系数为13.6w/m2k，其中当量辐射换热系数为5.68w/m2k，对流换热系数为9.48w/m2k，并且送风速度越高、送风温度越低，地板与其他壁面的辐射换热量有一定程度的降低，但总供冷量增加；在整个实验中地板温度始终高于地板上层空气的露点温度，并未发现有结露现象；室内空气温度梯度能满足0.1m-1.1m的温差小于3℃的要求，并且适当提高送风温度可以进一步提高人体的热舒适性。

For this reason, we choose to use the yangmai chemical plant we go in for days TM－200S coupling agent to improve the gum resin solutions to increase the strength on adhesive surface adhesion, so as to effectively prevent plastic from bonding surface on exuvaite and atrippint, both the ink system glue resistance of performance and increases some difficult sticky material and low molecular resin Sol, pigments and fillers between the adhesion strength and packaging business card printing and membership card making ink film luster and water washable.

不不差此，我们采取仪征天扬冻工厂的TM－200S偶联剂来恶化树脂溶液的胶接洽强量，补充胶液不不差胶粘暗不天的粘附辛，从而灵验不天制止胶层从胶接暗不天零落和剥落，既促退了油不朱编制胶液耐湿热功用的本能机能，又补充了一些难粘质料和矮不合子树脂溶胶、颜填料之间的胶接强量及包装制卡和会员卡制作不朱膜的平泽量和火可洗性。

FeSi nanoparticles were synthesized via thermal decomposition of iron pentacarbonyl in the solution of dioctyl ether, stabilizers oleic acid and oleylamine. The TEM images showed that FeSi nanoparticles had cubic shape, but it seemed that the composition was not uniform. According to the EDS results, the Fe:Si ratio of gray-uniform nanopaiticles was almost 1:1, and blacker FeSi nanoparticles contained more Fe atoms. Although FeSi didn't have uniform structure, it still could be proved that the incorporation of Fe and Si existed in a single nanoparticle. All possible structure, lattice, binding, morphology, surface condition would be discussed. These results indicated that perhaps FeSi2 was the main structure of the new products; however, due to incompletely combination and less synthesized time, it might still contain some part of Si and Fe structure. Besides, FeSi nanoparticles preserved the optical properties from Si atoms, but the PL intensity was much lower. The maxima PL peak appeared at 388 nm with the excitation at 300 nm. Their saturation magnetization, remanent magnetization and coercivity were measured by the SQUID, exhibiting their nearly superparamagnetic behavior.

利用热裂解系统可成功将研磨矽奈米粒子及五羰铁结合，制备出铁矽奈米粒子；从穿透式显微镜照片可知其粒子呈现立方体型态，但颜色深浅及组成不均，EDS结果则显示颜色均匀之粒子铁与矽之组成大致为1：1，颜色较深之粒子则含有较高量的铁元素；尽管组成比例并不统一，但单颗粒子同时含有矽与铁两种元素，初步说明铁矽奈米粒子之形成；进行多种结构与表面分析并探讨所有可能之键结、结构及表面元素后，推测铁矽奈米粒子可能以FeSi2之结构形成，并同时包含未重组完成的矽及铁之结构；利用PL分析得知铁矽奈米粒子确实保留矽之放光特性，并在300 nm激发光源下，於波长388 nm处有一最强放光特性峰，但整体发光效益不及研磨矽奈米粒子之结果；最后，利用超导量子干涉磁化仪量测其饱和磁化量、残留磁化量、与矫顽磁力，发现磁滞现象并不明显而几乎呈超顺磁性。

By measuring diurnal photosynthesis and transpiration, three urban tree species in Northern China of Sophora japonica, Acer mono Maxim and Platanus orientalis were studied so as to appraise theirs alleviative effect on urban heat island and their ecological benefits of carbon dioxide absorbing capacity, oxygen producing, and cooling and humidification.

选择华北地区3种常见的城市绿化树种国槐、元宝枫、法桐，测定其光合速率及蒸腾强度，据此估算其固碳量、释氧量和降温增湿量，并量化评价3种绿化树种的生态学效应及对城市&热岛效应&的减缓作用，时间尺度为日。

Through the flue gas and air characteristic analysis in supercharged boiler,the results showed that the value of parameters would increase with the increase of fuel consumption.And volume heat load of the furnace, fuel consumption, heat change between flue gas and convective heating surface and evaporation value would increase with the increase of compression ratio.The heat calculation would be different because of dissimilar thermal calculation in the turbo-compressor when the boiler load was changed.As the boiler load increased,heat loss in the turbo-compressor would increase and the efficiency of the boiler would decrease.The results of the boiler start-up simulation showed that the time of start-up would decrease with the increase of flue consumption ,but instantaneous pressure amplitude would increase.Steam water"s dymamic diversification would be more complex than flue gas"s,and dynamic characters of their parameters would be changed due to different boiler load and disturbance variable,which was shown by results of the simulation when boiler load was changed.

通过分析增压锅炉内的空气、烟气参数特性，发现随着锅炉负荷的增加，空气和烟气的各项参数值都相应的增加；炉膛容积热负荷、锅炉的燃料负荷随着增压比的提高成比例增加；随着增压比的增大，烟气与对流受热面的换热增加，蒸发量随之增加；由于涡轮增压机组在不同负荷下的热力计算不同而造成增压锅炉在不同负荷下的热平衡计算的不同；锅炉增压机组的总的热损失随着锅炉负荷的增加而增加，而增压锅炉的热效率随着锅炉负荷的增加而减少；锅炉启动模拟仿真结果中发现，锅炉启动时燃料量增加，锅炉的启动时间就会减少，但是瞬时升压速度会增加；而动态负荷变化模拟仿真结果中发现，锅炉汽水侧的变化相比烟气侧更为复杂，且在不同负荷和不同扰动量下，烟气侧和汽水侧的重要参数动态特性是不同的。

This article summarises the chemical reactions in milk during heat treatment, analyzes the properties of several indicators for heat damage , such as heat-sensitive enzymes, denatured proteins, the products of Mailliard Reaction and isomerised lactose.

本文分析了牛乳在热加工过程中的化学变化，介绍了几种牛乳热损伤监控标识物(如热敏性酶类，蛋白质变性产物，美拉德反应产物和乳糖异构化产物)的特点，并详细论述了已有的牛乳热损伤监控技术：对变性β-乳球蛋白含量的监控，对糠氨酸和乳果糖含量综合水平的监控，对羟甲基糠醛含量的监控，以及以变性蛋白质(以色氨酸的荧光强度计，FTry)和美拉德反应荧光产物的聚集量为基础，评估牛乳热加工损伤程度的FAST方法。

In practical study, the essential flow is""on the basis of the study of the faults, strata denuded thickness and original thickness, analyzing the controlling effect of the faults to the sedimentation and denudation, and combined with the areal geology background, reconstructing the basin prototype of each stage"". 2. As the basic theories and methods of the calculation of the denuded thickness, such as, the methods of cosmogenic nuclides, wave equation, apatite fission track, structural sections, acoustic wave, vitrinite reflection, etc, were argued detailedly , and their applicable ranges were analyzed , the denuded strata thickness of each structural layer layer of pre-Tertiary was reconstructed.

对宇宙成因核素法、波动方程法、裂变径迹分析法、构造横剖面法、声波时差法、镜质体反射率法等计算剥蚀量方法的基本原理进行充分论证、改进，分析了各方法的适用范围，在此基础上，综合充分运用上述方法，计算了济阳坳陷前第三系各构造层在不同时期的剥蚀量，绘制了中生代时期古生界顶面的地层剥蚀量等值线图、新生代时期古生界顶面的地层剥蚀量等值线图、白垩纪沉积时侏罗系剥蚀等值线图、新生代沉积期白垩系剥蚀等值线图、新生代沉积期侏罗系剥蚀等值线图等图件，并通过对古生界地层的热变质程度分析，确定了有1500～2000m的早、中三叠世的原始沉积地层在晚三叠世被剥蚀殆尽。3。

For the condition where both outlet states of cold plate are at superheated states, the mass flowrate for the fixed heating load is marginally higher than that of the smaller heating load, and the difference is insensitive to the rise of heating load. For this situation, the effect of accelerational pressure is negligible, and it is mainly attributed to two-phase/single-phase distribution pertaining to the effect of heating load.

若两冷板的出口均为过热状态下，固定热负载一端的流量会略多於施加瓦数较高的一端，且其差异量会随热负载不同而缓慢增加，在此一状况下，则加速度压降可以忽略不计，其原因在於单相／两相流在热负载下单相区与两相区所占的比重不同所致。

According to the technological characteristics of soaking furnace of CSP line, the 3D-unsteady mathematical model of the loss of iron scale in soaking process was established with the experimental reheating furnace as instance by utilizing the methods of equivalent thermal resistance and equivalent mass. The effect of thickening of iron oxidation on heat transfer between gas and slab was considered in the model of loss of iron scale.

根据紧凑式带钢生产均热工艺特点，利用等效热阻和等效质量法，以实验均热炉为研究对象，建立三维非稳态钢坯均热过程氧化烧损数学模型，考虑氧化层的增长对传热过程的影响对氧化烧损量进行计算。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。