量热

The results show that the increasing Marangoni number will lead to more nonlinear distribution of temperature field, but streamfunction of the cell center; vorticity on the wall and peak value of velocity diminish first, then increase, finally lose stability. The thermocapillary convection in the whole liquid zone appears to get stronger along with the augmentation of Prantal number. The effect of increasing of Biot number on temperature and flow fields is not obvious although the convection is strengthened a little. As increasing the aspect ratio A, thermocapillary convection induced by temperature gradient and liquid viscosity becomes stronger.

结果表明：温度场的非线性分布随着Ma数的增大而加剧，但对流涡胞中心流函数、壁面涡量和轴向、径向速度峰值并不象温度场随着Ma数的增大而单调增大，而是先减小，然后增大，最后失稳，表明Ma数对热毛细对流的影响比较复杂，针对不同的物理模型，会导致完全不同的流态；Pr数愈大，流体的热扩散能力在粘性扩散与热扩散能力之比中愈占支配地位，当Ma数一定时，热毛细对流随Pr数的增大在整个液体区域内有增强的趋势；Bi数增大，热毛细对流有所增强，但不甚明显；A的增大使得由温度梯度和流体粘性诱导的热毛细对流随之增强。

Dynamic mechanical analysis,mechanical properties and the thermal dilatability measurements were used to study the effects of SF content on dynamic mechanical properties,impact strength,bending strength,bending modulus,specific strength,specific modulus,wear resistance and thermal dilatability.

采用动态力学、力学性能、热膨胀性能等测定研究了剑麻纤维的加入量对复合材料的动态力学性能、冲击强度、弯曲强度、弯曲模量、比强度、比模量、耐磨性能、热膨胀性能的影响，用扫描电镜观察了材料冲击断面和磨损面的形态。

Compared with the graphite, the coefficients of friction of the RL-C/C are lower under the same load of about 0.08-0.12, and the increasing range of the volume losses are still lower than those of the graphite. Compared with the SL pyrocarbon material, the COF and the volume loss of the SL-C/C are about 0.02-0.05 and 0.2 mm^3, lower than those under the same load. The COFs of most RL-C/C and SL-C/C specimens remain stable or decrease slightly with time, while those of the graphite and pyrocarbon specimens increase. The thickness of the integrated friction film of the RL-C/C decreases with load, but the wear surface of the SL-C/C is rough. Tough the wear surface of the graphite is integrated, the serious abrasive wear make the debris move easily and accumulate on the edge of the wear trace to form a restacked morphology. On the wear surface of the pyrocarbon material, some loosed debris, circular worn holes and flake worn out pyrocarbon has been found.

结果表明：PAN炭纤维改善C/C复合材料的摩擦磨损行为；在实验载荷范围内，与高强度石墨材料相比，含RL炭C/C复合材料的摩擦因数降低0.08~0.12；体积磨损量增幅降低；与热解炭试样相比，具有SL炭C/C复合材料的摩擦因数降低0.02~0.05，体积磨损量低0.2立方公厘左右；随着时间的延长，大部分C/C复合材料的摩擦因数基本相对稳定或呈小幅下降，而石墨、热解炭块的摩擦因数均呈不同幅度的上升；具有RL炭的C/C复合材料摩擦表面膜厚度随载荷增加而降低，具有SL炭的C/C复合材料摩擦表面较粗糙；高强石墨能形成较完整致密的摩擦膜，但磨粒磨损严重，磨屑易在摩擦膜边缘形成层状堆积；热解炭块摩擦表面磨屑堆积松散，有较多的孔洞以及热解炭层整体剥落的形貌。

Compared with the graphite, the coefficients of friction of the RL-C/C are lower under the same load of about 0.080.12, and the increasing range of the volume losses are still lower than those of the graphite. Compared with the SL pyrocarbon material, the COF and the volume loss of the SL-C/C are about 0.020.05 and 0.2 mm3, lower than those under the same load. The COFs of most RL-C/C and SL-C/C specimens remain stable or decrease slightly with time, while those of the graphite and pyrocarbon specimens increase. The thickness of the integrated friction film of the RL-C/C decreases with load, but the wear surface of the SL-C/C is rough. Tough the wear surface of the graphite is integrated, the serious abrasive wear make the debris move easily and accumulate on the edge of the wear trace to form a restacked morphology. On the wear surface of the pyrocarbon material, some loosed debris, circular worn holes and flake worn out pyrocarbon has been found.

结果表明：PAN炭纤维改善C/C复合材料的摩擦磨损行为；在实验载荷范围内，与高强度石墨材料相比，含RL炭C/C复合材料的摩擦因数降低0.08~0.12；体积磨损量增幅降低；与热解炭试样相比，具有SL炭C/C复合材料的摩擦因数降低0.02~0.05，体积磨损量低0.2 mm3左右；随着时间的延长，大部分C/C复合材料的摩擦因数基本相对稳定或呈小幅下降，而石墨、热解炭块的摩擦因数均呈不同幅度的上升；具有RL炭的C/C复合材料摩擦表面膜厚度随载荷增加而降低，具有SL炭的C/C复合材料摩擦表面较粗糙；高强石墨能形成较完整致密的摩擦膜，但磨粒磨损严重，磨屑易在摩擦膜边缘形成层状堆积；热解炭块摩擦表面磨屑堆积松散，有较多的孔洞以及热解炭层整体剥落的形貌。

When the amount of water is fixed, GTE reduces with the increasing of water-cement ratio and increases when cement content is fixed. At first, the GTE changes dramatically, but 28 days later, it approaches a stable value.

水灰质量比的影响则取决于水泥用量和用水量的相对关系，当用水量一定时，热膨胀系数随水灰质量比的增大而降低；当水泥用量一定时，热膨胀系数随水灰质量比的增大而升高。

The results show that dynamic softening is easy to occur in these ingots and flow stress becomes steady finally; the material constants of hot deformation are procedural parameters that stress-level coefficient α, strain rate sensibility exponent m and deformation activation energy Q are all increased with strain increasing, while stress exponent n is decreased gradually; the values α and m of the alloy homogenized are the biggest and the value n is the smallest, dynamic softening effect of the alloy is the most obvious, which can deform evenly; influence of strain on the value Q of the alloy homogenized is a little and the average value of Q is only 176.5kJ/mol, so the alloy is easy to deform; the alloy matrix shows the regular recrystallization grains when the strain is 50%; dislocation cell structure re-formed in the grains with increase of strain.

结果表明：经不同处理的Al-1Mn-1Mg合金均易发生动态软化并最终呈现稳态流变特征；热变形材料常数是过程量，随应变量的增加，应力水平参数α、应变速率敏感性指数m和热变形激活能 Q 随之增大，而应力指数 n 则逐渐减小；均匀化退火后，铝合金的α和m值最大而n值最小，动态软化效果最明显且变形均匀，在该状态下，铝合金的 Q 值受变形量影响小，平均仅为176.5kJ/mol，易进行热变形；当应变量为0.7时，基体呈现规则的再结晶晶粒组织，随着应变量的增加，晶内重新形成了位错胞结构。

The experiment acquired pressure distribution and circulating rate under three fluidizing velocity (3.5m/s、4.5m/s、5.5m/s) and different media load. An experimental equation was acquired between circulating rate and the distribution of the pressure. And the relation between the circulating rate and the opening rate of the valve connecting the returner and the EHE was carefully discussed as well as the relation between the pressure of the EHE and the flow rate of the fluidizing air.

得到三种流化风速下（3.5m/s、4.5m/s、5.5m/s）不同装料量所对应的主床床体压力分布和物料循环量，得到循环量与压力的分布和流化风速的本实验台上的经验公式，并通过测量返料器通向外置换热器机械阀开度和返料量的关系，得到旋风分离器中下落物料进入换热器和直接进入主床的比例关系，同时测得换热器中压力和送风量的关系。

The results show that the optimal value of CoCl2 concentration is 0.2 mol/L and the maximum adsorbed amount is 19.674 mg/g onto this adsorbent. The adsorption capacity of phosphine onto CoCl2-modified ACF decreases with the increase of temperatures. The maximum absorbed amounts are 19.674 mg/g at 298 K, 13.537 mg/g at 313 K and 11.087 mg/g at 328 K, respectively. It is found that the Freundlich equation is more suitable for the description of phosphine adsorption process than the Langmuir equation. The isosteric heat of adsorption decreases with the increase of the surface loading on CoCl2-modified ACF, which means that CoCl2-modified ACF adsorbent has an energetically heterogeneous surface. Meanwhile, adsorptive phosphine removal performance may be a dominant of physical adsorption when the heat of adsorption is 16-24 kJ/mol, the CoCl2-modified ACF adsorbent will be one of the candidates for tail gas purification of airtight calcium-carbide furnace and recycle of phosphine.

研究结果表明：浸渍液浓度最佳值为0.2 mol/L，此改性ACF对PH3的饱和吸附量为19.674 mg/g；PH3在CoCl2改性ACF上的吸附量随温度升高而迅速降低，在298，313和328 K时PH3的饱和吸附量分别为19.674，13.537和11.087 mg/g；Freundlich吸附等温方程较好地模拟了PH3在改性ACF上的等温吸附；PH3气体在改性ACF上的等量吸附热随吸附量的增大而减小，表明改性ACF吸附剂表面能量的不均匀性；吸附热在16~24 kJ/mol范围内，过程为物理吸附，有利于密闭电石炉尾气的净化。

The experimental and analytical results show that the axial rigidity of the corrugated pipe is 23.0 percent of the bare pipe with the same thickness and diameter,and the thermal compensation performance of the former is 2.27 times the latter's under equal-stress condition.By using corrugated pipe bundle instead of the bare pipe bundle with the same stiffness as its tube sheet,the axial thermal compensation can be increased by 40.4 percent,and the corresponding pulling-out force is 53.2 percent of that of the bare pipe bundle.

研究结果表明，波节换热管单管的刚度为相应光管的23.4%；在最大应力相同的条件下，波节换热管的轴向热补偿量为相应光管的2.27倍；在光管管束与壳体等刚度条件下，用波节管管束代替光管管束，轴向热补偿量可提高40.4%，相应的拉脱力为光管管束的53.2%。

So the research on the thermo-economics analysis of thermal power plant is significant, this paper focuses on this field and gets some conclusions as follows: Based on Equivalent Enthalpy Drop Method and Cyclical Function Method, a conception, New Heating Steam Flow, is proposed and defined in this paper, which makes it possible to separate the cogeneration circle into condensate steam circle and heating steam circle and to get the new power equation and calculate the Rate of Electrical Power Generation by Heating Steam with Net Equivalent Enthalpy Drop.

在等效热降法的基础上，结合循环函数法的循环分析理论，通过引入热化新蒸汽量的概念，使得常规抽凝供热机组的纯凝汽循环与供热抽汽循环得以分离，从而得出了相应的供热机组汽轮机的功率方程，并实现了热化发电量与净等效热降计算的统一，最终完成了利用等效热降法对供热机组热化发电率的计算，使得已在凝汽机组中应用成熟的等效热降法可以方便地应用于供热机组，进行经济性分析和计算。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。