量压的

In this paper, the dynamic compressing experiments for the matrix material of the tungsten alloys which have been three different deforming(0%、 32.6%、 44.6%) processed have been performed by the experimental technology of separated Hopkinson pressure bar and many accurate datum have been obtained. Also the three materials have been compared with each other and analyzed. The results show that the optimized values are in a certain range to optimize the materials by changing their deforming technology. The parameters of constitutive model of Johnson-Cook have been fitted based on the datum. Then proceed to the next step, adiabatic shear band of these three matrix materials has been analyzed with finite element method. The result shows that the relations between stress and strain are different because of the differences of technical process of the three materials, but they are in great commonness in the material experiment and in great coherence in the distribution of time and space, which can been seen from the space distributing figures of plastic strain.

利用分离式Hopkinson压杆实验技术对三种不同变形量(0%、32.6%、44.6%)钨合金基体材料进行动态压缩实验，取得大量精确的数据，对比分析三种材料，结果表明通过改变变形量对材料进行优化，其变形量的优化值是有一定范围的；本论文拟合、确定了钨合金基体材料Johnson-Cook本构模型参数并对三种基体材料绝热剪切带进行有限元分析，结果表明三种材料由于工艺流程的不同，应力应变关系也不尽相同，但从塑性应变的空间分布图上体现了材料很大的共性和时间以及空间分布的一致性。

The small size particles produced during ferrovanadium sizing operation are formed into nitrided briquette so as to obtain nitrided ferrovanadium, The effect of ferroalloy size, pressure, nitriding temperature and nitniding time was studied on the nitrogen content of the product.

对高钒铁合金精整过程中产生的细颗粒物料进行压块渗氮，得到氮化钒铁产品，研究了合金粒度、压块压强、渗氮温度、渗氮时间对产品含氮量的影响。

As for coseismic deformation of Chi-Chi earthquake, the footwall of Chelungpu Fault moved southeastwards 0.3-1.5 m, and the value was increasing toward the fault; the hanging wall moved northwestwards 1.4-7.0 m, but the value was smaller south of the Choshui River. After the Chi-Chi earthquake, the hanging wall of Chelungpu Fault was still moving west-northwestwards and kept uplifting, while the footwall gradually changed direction from ESE to WSW or even WNW, clockwise resuming to inter-seismic deformation pattern. It is interesting to notice that despite the largest coseismic deformation in the northernmost segment of Chelungpu Fault, the post-seismic deformation peaked around the epicenter of Chi-Chi earthquake.

集集地震之同震变形，在车笼埔断层下盘向东南方向位移0.30~1.5 m，且越靠近断层位移量越大；车笼埔断层上盘则向西北方向大幅位移约1.4~7.0 m，浊水溪以南的位移量较小；集集地震以后之震后变形型态，以车笼埔断层为分界，上盘在震后向西北西方向位移的型态仍与同震时相同，下盘由同震时一致性的向东南东方向，逐步向西北西或西南西方向位移，亦即在车笼埔断层下盘有逐步依顺时针方向回归至震间的滑移型态；另就位移速率而言，虽然同震变形最大地区在车笼埔断层北端，但其震后的变形量最大地区，却集中於震央位置附近；就地震循环而言，震后的6年期间仍处於地层压密重整阶段，尚未回归至该区震间阶段的位移状态。

Proton generated from a Cockroft-Walton accelerator in the energy range of 30-100 keV were appropriately collimated and made to pass through a 10 g/cm^2 carbon foil. After Rutherford scattering, proton uniformly irradiated TLDs which were placed at the 20° behind and 20 cm away from the carbon foil. We used a channeltron behind TLD holder as the proton detector.

由Cockroft-Walton加速器提供之质子源，能量在30~100keV间，经准直后通过一10 g/平方公分之碳膜做拉塞福散射，散射后之质子均匀打在置於其后20°的压克力置装器内的热发光剂量计，利用压克力置装器后之一电子倍增器作为量测质子工具。

The results show that increasing the ball numbers and mandrel extension length may reduce the ovalization, but leads to more remarkable wall thinning; the ovalization becomes more severe with the larger bending angle; the smaller the relative bending radius, the larger the ovalization is; the ovalization and wall thinning degrees are both smaller in the case of pressure die with dry lubricant; and under the same bending condition, the ovalization of LF2M tube is larger than the one of 1Cr18Ni9Ti tube.

结果表明，增加芯头个数与芯棒伸长量都能减小弯管的截面畸变，但两者都导致弯管壁厚减薄量增大；随着弯曲角度的增加，截面畸变越严重，相对弯曲半径越小，无芯棒与芯头支撑段弯管的截面畸变愈严重；在压块无润滑情况下，弯管的截面畸变和壁厚减薄量都小，并且在同等弯曲条件下，1Cr18Ni9Ti弯管的截面畸变小于LF2M弯管。

The operation parameters include different starfruit weight, flow rate, extraction time, extraction pressure, extraction temperature, different addition volume of ethanol cosolvent, ethanol concentration and other extraction way.

以杨桃量、泄压流速、萃取时间、萃取压力、萃取温度、共溶剂乙醇的添加量与不同萃取方式等为操作变因，配合一次一变因法来进行探讨，以找出最佳萃取条件。

The controlled variables of ball milling are the negative pressure in the input, the temperature in the output and the given coal storage of the ball mill.

球磨机制粉系统的控制量为存煤量、出口温度和入口负压。

Effects of volume of test panel,length of clad lines,overlapping length,lapping pass number of clad layer and restrictive planten on crack ratio of clad layer were investigated.

研究了试板体积、熔敷层长度、搭接量、熔敷层搭接道数及压板拘束对熔敷层裂纹率的影响，结果表明随试板体积增大、熔敷层长度增加、搭接量增大和熔敷层搭接道数增多，熔敷层裂纹率升高。

Needle valves are non-compensating devices the orifice sige will regu late the flow through the valve in proportion to the sgure root of the pressure differential across port 1 and 2,therefore naking these valves suitable only where the load remains constant.

依赖它们在回路中的位置可作量入，量出，旁伸控制。●孔口流量正比压降平主根因此只适合固定负载，变动负载要用压力补偿阀。

The control means are to adjust the recycle damper, the hot air gate and the coal feeder.

给煤量、再循环冷风量及热风量的任一改变都将影响到入口负压、出口温度和存煤量。

We have no common name for a mime of Sophron or Xenarchus and a Socratic Conversation; and we should still be without one even if the imitation in the two instances were in trimeters or elegiacs or some other kind of verse--though it is the way with people to tack on 'poet' to the name of a metre, and talk of elegiac-poets and epic-poets, thinking that they call them poets not by reason of the imitative nature of their work, but indiscriminately by reason of the metre they write in.

索夫农 、森那库斯和苏格拉底式的对话采用的模仿没有一个公共的名称；三音步诗、挽歌体或其他类型的诗的模仿也没有——人们把&诗人&这一名词和格律名称结合到一起，称之为挽歌体诗人或者史诗诗人，他们被称为诗人，似乎只是因为遵守格律写作，而非他们作品的模仿本质。

The relationship between communicative competence and grammar teaching should be that of the ends and the means.

交际能力和语法的关系应该是目标与途径的关系。