量出

SDRAM is used as image storage, which can store many frames image data to provide the foundation for the correlation operation between frames. FIFO is a data buffer for real-time image. All of these make the image processing system simple design, decreasing the write-read time and solving the question of transmission and delay, and allowing the data processing and the data grabbing at the same time. The processed results can be output in 20ms, so the bandwidth of the C6000-based image processing system is improved.

系统采用SDRAM作为图像存储器，可以存储多帧图像数据，为实现帧相关运算奠定了基础，实时图像数据采用FIFO作为缓存，使系统设计简单，读取速度快，解决了数据传输的瓶径问题，同时也减少了传输延时，实现了对图像数据边采集边处理，减少了系统的滞后时间，当场给出电视脱靶量，提高了图像处理系统的带宽。

Under the inducing and application of current network design methods to CIM-CN design, author presents some algorithms and methods in accordance with the characters of CIM-CN, for example splitting a large CIM-CN into several subnetworks using traffic matrix, synthetical review target architecture and review methods for CIM-CN.

在归纳、整理运用现有网络设计方法于CIM-CN设计过程中，作者还针对CIM-CN的设计特点提出了用通信量矩阵运算划分CIM-CN子网的算法，优先级MAC存取算法以及CIM-CN综合评价指标体系结构及评价方法；作者还给出用专家系统进行CIM-CN设计的框架与思路并进行了初步探讨。

A series of theoretical and experimental studies on the microstrip patch antennas with dielectric superstrates is carried out systematically. Firstly, a comprehensive survey of the microstrip antenna technology and its theories are presented. Then, two analysis techniques, named as the spectral domain Green's function method and the spectral domain integral equation method are developed. The SDGF method is a simplified analysis technique, which takes advantage of the spectral domain immittance approach to find the dyadic Green's function for the stratified media, and obtains the complete closed-form formulas for radiation patterns, directivity, efficiency, gain etc. Some interesting calculated results are presented. The SDIE method is capable of determining resonant frequency, radiation characteristics, input impedance etc, for the covered microstrip patch antennas. Comparing with other full-wave analyses it reduced computation and mathematical labour remarkably. The singularities near the pole location of the surface-wave modes and the difficulty of the integral computation over infinite range of oscillating integrands are dealt with actively and documented well. Results predicted by the SDIE method agree extremely well with our experimental results for resonant frequencies of various superstrates. The superstrate effects on impedance and radiation characteristics also have been investigated experimentally so that the gap due to lack of measured data and computed results for multi-layered superstrate has been filled to some degrees and two useful observations have been achieved for weakening the resonant frequency shift and optimizing the microstrip antenna gain. As a meaningful application, the design and analysis of a 4×4 patch array are introduced.

实用微带天线普遍加介质覆盖层来防护热，物理损伤和环境影响，也可能在飞行或严酷气候条件下自然形成覆盖层本论文对带介质覆盖层的微带贴片天线系统地作了一系列理论和实验研究首先，对微带天线技术和理论作了全面的综述然后，发展了两种分析方法，称为谱域格林函数法和谱域积分方程法SDGF法是一种简化的分析技术，它利用谱域导抗法来求得分层媒质的并矢格林函数，并得出方向图、方向性系数、增益等参数的完整的闭式公式，给出了一些令人感兴趣的计算结果SDIE法能确定介质覆盖微带天线的谐振频率、辐射特性和输入阻抗等与其它全波分析方法相比，它明显减小了计算量和数学工作量已有效地处理了表面波模极点附近的奇异性和对振荡的被积函数的无限区间积分计算的困难对于不同覆盖层情况下的谐振频率，由SDIE法所预示的结果与我们的实验结果吻合得很好对于覆盖层对阻抗和辐射特性的影响也已作了实验研究这在某种程度上填补了缺少实验数据和计算结果之间的间隙，并得出了缓解谐振频率偏移和优化天线增益的两点有用的结论作为有意义的应用，介绍了一个4×4元矩形贴片天线阵的设计和分析。

The local stress and average stress in different phases for a particle or a fiber with a graded interphase embedded in an infinite matrix under a general macroscopic loading are derived, then Mori-Tanaka and the generalized self-consistent methods have been used to evaluate the effective elastic and viscoelastic properties of the composites.

首先给出了具有沿径向连续变化界面层的颗粒或纤维放在无限大的基体中在静水压力和纯剪切载荷作用下的局部关系，然后利用Mori-Tanaka方法和广义自洽方法分别得到相应的复合材料的有效弹性模量和粘弹性中的储存和耗散模量。

So it is important to design an efficient attitude scale which not only can show the surveyors intention but also inflect the enough information of the respondent.

目前态度调查通常是通过量表的形式，所以如何设计出一个有效的态度量表——不仅要充分体现调查者的意图，还要使调查数据全面地反映被调查者的信息——就显得尤为重要。

The warming caused by a given increase in carbon dioxide can be calculated on the basis of laboratory measurements which show how much infra-red radiation at which specific wavelengths carbon dioxide molecules absorb.

实验室里可以量测二氧化碳分子对不同波长红外线辐射的吸收量，以此为基础，可以计算出某程度二氧化碳增加所能造成的暖化。

Based on ink supply's effect on printing production quality an through analysis of ink supply control method, PC controlled ink supply experimental system is developed.

印刷机油墨供给量对印刷质量有重要影响，通过分析印刷机输墨机构和控制方式，研制出微机墨量控制实验系统。

In chapter five, the application of the gray/depth image in computer image generation is discussed. A new method based on real time insert in three dimensional space is introduced. It is different with normal graphics and image method. Its property is animation scene and invariable generation time. Two simplified mode and a general mode of space insert is analysis. With all kinds of relativity, the fast increase algorithms are presented. Computer simulation is executed and condition of real time is estimated.

在第五章中，讨论了灰度/深度图象在计算机图象生成的应用，提出了用实时三维空间内进行CIG的新方法，它不同于常规的图形方式和图形方法，它具有生成画面逼真度高、运算量固定，仿真内容可变的特点，具体分析了三维空间内插的一般形式和两类常见退化形式，充分利用内在和相关的加速技术，给出了快速增量算法并作了模拟实现，估计了实时条件要求的计算量。

Distinction instillment different concentration antigen.

分别滴加不同浓度的抗原使其发生反应，测量傅里叶变换红外谱和加入抗体前后反射谱的变化，结果表明硅烷化效果明显，生物抗原较好的固定，抗原抗体反应前后反射谱有明显的红移，且红移量于滴加抗原浓度增加而增加，并且呈现出良好的非线性关系。

It performed the landing operation using Instrument Landing System during the landing phase, and crosswind and sudden event would be the main effect which caused the pilot mental workload difference in NASA Task Load Index and heart rate.

就不同环境条件的探讨，从NASA工作负荷量表及心率变化比的二项指标的检验中，显示出侧风与突发事件为造成飞行员於降落阶段时心智负荷差异的主要因素。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。