采用的

The air cylinder jacket is an important spare part of the engine, it is usually produced by the flowing water line in batches, the precise of it"s production is very high.Generally specified equipments,tongs and cutting tools are adopted in it"s production,So in the course of the development of the air cylinder jackets CAPP, specified equipments, tongs and cutting tools must be considered.

气缸套是发动机的重要零件，其生产通常是采用流水线批量进行的，气缸套零件的加工精度高，工艺过程复杂，在生产过程中通常采用专用的设备，夹具和刀具，因此气缸套CAPP系统必须考虑生产过程中采用的设备、夹具和刀具。

There are many noise sources in measuring the seismometer transfer function, the main noise sources are investigated. The method of cross-special analysis is presented, flow process diagram of computing is given, the algorithms are discussed in detail, such as low-pass digital filter, computing of seismometer transfer function initial values, time domain convolution, bilinear transformation, estimation of power spectrum and cross-spectrum, window functions and preprocessing of measuring data etc.

在地震计传递函数测试过程中的存在多中噪声，本文分析了主要的噪声来源；介绍了用互谱分析方法测试地震计频率特性的基本原理和方法；给出采用该方法确定地震计传递函数的算法流程图；并对计算过程中采用的低通滤波器、地震计传递函数的初值确定方法、卷积运算方法、自谱和互谱估计、采用的窗函数和测试数据的预处理进行了详细讨论。

In addition, in the design of software configuration it analyzes the realization of the high-speed data sampling program and intelligent information processing and monitoring. At last it introduces function of sbftware of systems analysis in brief.The operation demonstrates that the brand-new monitoring method of the monitoring system can acquire the operation axis of large-scale rotary kiln by rule and line on the operation position, and it is a break-through in real-time monitoring method.

现场运行表明，该监测系统所采用的全新的监测方法能够在十分恶劣复杂的现场环境中准确地获取大型回转窑的运行轴线参数，对大型回转窑实时监测方法是一种新的突破；同时，采用的特制电涡流传感器及微机软件进行误差补偿极大地提高了监测系统的测量精度：采用的模糊自适应智能滤波方法有效地滤除了本系统恶劣环境下各种干扰因素。

The oil sewage disposed process is a complex disposal technique. The disposal process is more difficult for the change of PH Flux temperature of raw water and the other polluted quality. At present the disposed water by the system of oil of sewage is unstable and high cost. Now the method for the oil of sewage have physics chemistry physical chemistry and biology etc. In the every disposed method has its own specially, Basis of the oil sewage condition of power plant. The text use chemic method. Another word is method of Flocculation-deposition. Injecting Dosage into sewage. Making small suspends grain and the electrophorus colloid gather into bigger colloid and deposit. Separated it from water and purify the oil sewage. Make disposed oil water up to grade.

含油污水处理工艺是一个复杂的处理过程，在处理过程中由于受到原水浊度、PH值、配水流量、原水温度和其他水质污染等因素的影响，处理难度相当大，现时的含油污水处理系统普遍存在处理后的水质不稳定和处理成本高等问题，国内外含油污水处理采用的方法有物理法、化学法、物理化学法和生物法等，每种处理方法都有自己的特点，结合电厂含油污水的情况，本文主要采用化学法，具体来说是采用絮凝沉淀的方法，通过向废水中投加混凝剂，使细小的悬浮颗粒和带电胶体微粒聚集成较大颗粒而沉淀，使其与水分离，使含油污水得到净化，使处理后的废水各项指标达到排放标准。

By using the CFD software FLUENT, the inner-flow field of centrifugal fans with ruled-surface impeller versus with enveloping surface impeller has been simulated. The static pressure distribution, the dynamic pressure distribution, the total pressure distribution, the turbulent intensity and the speed vector of the two kinds of centrifugal fans are then analyzed and compared. From the calculating results, we found that the pressure distribution, the speed vector and other parameters of the two kinds of centrifugal fans are basically same. This implies that the tool-path generating arithmetic for the machining of the impeller can meet the aerodynamic requirements of the centrifugal fan. Furthermore the method can provide proof for designing department to establish sound manufacturing tolerance for impeller.

最后采用CFD软件FLUENT，利用标准k-ε湍流模型，采用分离隐式求解器，分别对直纹面叶轮离心通风机和包络面叶轮离心通风机整体风机内部三维流场和单个通道流场进行了数值模拟计算，在计算结果的后处理中，对相同坐标值处的静压力、动压力、湍流强度和速度矢量等参数进行了分析与比较，结果表明：在相同的计算参数条件下所得到直纹面叶轮离心通风机和包络面叶轮离心通风机内部流场差别不大，从而揭示所采用的叶轮数控加工的刀位规划方法的规划误差对流体机械动力性能的影响不大，这也为设计部门制定合理的叶轮加工公差提供了依据。

When other technics conditions are certain, we use the globosity aluminum powder of different particle diameter a to grind the flake of aluminum powder , with the particle diameter increase of the globosity aluminum powder, the particle diameter of the flake of aluminum powder will also become bigger immediately. 3, The ratio of grinding ball to aluminum powder is 20:1. 4,the grinding speed is 38 and 33 r.min alternate once h-our in the first 10 hours, and use the speed of 29 and24 per hour alternating revolving speed in the last 5 hours, this speed is fine to grind the flake of aluminum powder. 5, wet method ball-milling mainly adopt of help-milling agent as Bl. 6, influence of the research grinding time.

经系统的研究，得出如下结论：1、基本参数：采用200升球磨机，装入钢球200kg，原料铝粉：溶剂量=1：2，铝粉：钢球=1：20；2、当其它工艺条件一定时，用不同粒径的球状铝粉作为原料磨制片状铝粉，随着原料铝粉的粒径增大，所制得的片状铝粉的粒径也会随之增大。3、球料比我们控制在20：1.4、研磨前10小时采用速38和33r.min每小时交变一次，后5小时用29和24每小时交变的转速，这个速度是适宜磨制片状铝粉的。5、湿法球磨片状铝粉主要采用的助剂为复合助剂B1.6、研究研磨时间的影响。

Subsequently, the paper indicated how the incompliant lending came from the bank and company sides, and summarized several common incompliant patterns based on personal experiences. Those patterns are as follows: firstly,"used shell to give birth to eggs"by the medium and small developer; secondly,"unified distribution"by large developer; thirdly,"do in the darkness"used in hyper-investment or roll development by developer. The paper summarized the characteristic and fund operation process for each mode, and analyzed the influence and risk of incompliant lending loan to both banks and real estate markets.

接着，从银行及企业两方面阐述房地产违规信贷的成因，并凭借个人实务经验总结出几种常见的违规信贷模式，一是中小型房地产商采用的借壳生蛋型，二是大型房地产商采用的统一调配型，三是在项目超投资或滚动开发时采用的暗渡陈仓型，对每一种模式归纳了特点及资金流转过程，并分析了违规信贷对银行和房地产市场的风险。

Finally, the second option was identified as the recommendatory handling technology of heavy cargo wharf in Xiangjiaba, which could meet the needs of the safe and efficient transit.

本文系统的总结了目前重大件运输中常见的装卸工艺，针对向家坝重大件码头拟采用的3000t级滚装船采用滚装卸船工艺和1000t驳船采用顶推卸船工艺或吊装卸船工艺方案的工艺流程进行了详细的阐述。

The standard flow channel valve can be used: the United States NIBCO T-580-70 Valve; S-580-70 Valve (2), available to full-flow channel valve indented Path: The United States NIBCO T-585-70 Valve; S-585-70 Valve 2, check valve: Path DN65 valve should be used the following Swing Y-shaped structure, and in accordance with the United States valves and pipe fittings Manufacturers Standardization Society MSS-SP80 standards of manufacture, working pressure 125 lbs class, in line with the United States Society for Testing and Materials Standard Bronze ASTMB62 valve, configuration, Teflon flap valve seat, or seat configuration flexibility of the spring-driven lift-type check valve.

可采用的标准流道阀门：美国尼伯科T-580-70球阀；S-580-70球阀（2）、可采用的不缩径全流道阀门：美国尼伯科T-585-70球阀；S-585-70球阀 2、止回阀：通径DN65以下的止回阀应该采用Y形旋启式结构，并按照美国阀门和管件制造商标准化协会MSS-SP80标准制造，工作压力125磅级，符合美国材料试验协会ASTMB62标准的青铜阀体，配置聚四氟乙烯阀座阀瓣，或配置弹性阀座的弹簧驱动升降式止回阀。

Torque spanner used to screw big high-tension hexagonal bolt and testing should be receive torque adjusting before and after application.

高强度大六角头螺栓施拧采用扭矩扳手和检查采用的扭矩扳手在班前和班后均应进行扭矩校正。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。