部位

The invention discloses a disposable venous blood taking set, the front end thereof is a venous needle, the back end thereof is a vacuum tube needle, the middle thereof is a connection tube, the side of the venous needle is provided with a needle handle, an adhesive tape is arranged on the needle handle, the part on the adhesive tape which is near to the needle handle is provided with an adhesive region, and the part which is far away from the needle handle is provided with an opening region.

本发明公开了一种一次性静脉采血器，前端为静脉针，后端为负压管针，中间为连管，静脉针的侧边设置针柄，针柄上设置粘接带，粘接带上靠近针柄的部位设置粘接区、远离针柄的部位设置开启区。

Methods 80 health volunteers' skin biopsies samples from sun-exposed areas of the face, and non-sun-exposed areas.

对80例取自不同年龄志愿者的曝光部位及非曝光部位的皮肤组织进行HE染色、Weigert染色、苦味酸天狼猩红染色及免疫组化处理，采用显微形态观察和半定量分析。

This paper analyzes the reasons and positions of speed reducer leakage,and puts forword some solutions for different positions.

本文详细论述了减速机漏油的部位、原因，并针时不同的部位、原因提出了相应的解决方案。

The results show that the most dangerous position is near the joint of two-level series-wound mechanism, in which the failure happened easily.

从模态分析的结果可知，传动机构各构件危险部位多发生在靠近两级串联机构相连处附近，其失效多发生在这些部位。

Cut file, sawing skills by learning the grip, standing position, body movements, and many other points force factors and the impact of the traditional grip of the emergence of file-grip handle to stand up after slightly outside the site of the palm, when a file cut Force, after the file handle a gradual shift,"hold" to "grasp", resulting in the introduction file enough; saw grip handle full point higher than the thrust of the saw blade to install center hole of about 30mm, the high point of thrust is likely to result in the bow saw On both sides of the swing, resulting in a broken saw blade and saw seam askew.

锉削、锯削技能的学习是受握法、站立部位、身体动作、作用力点等诸多因素的制约和影响的，传统的握法出现握锉柄后顶住部位稍偏离手心，锉削时一用力，锉柄逐渐后移，&握&变成&抓&，造成锉刀推出力度不足；满握锯柄的推力点高于锯条安装孔中心约30mm，偏高的推力点很容易造成锯弓向两侧摆动，造成锯条折断及锯缝歪斜。

Sleep in the whole body relax, nose throat of the three sites are blocked, the narrow part of the impact of air flow, caused by vibration and resonance cavity of the different levels of noise.

人在睡眠时全身放松，如果鼻咽喉这三个部位有阻塞，气流冲击狭窄的部位，引起共鸣腔的振动而发出不同程度的响声。

For the proposed project the waste gas emission locations include: preheating furnace of hard alloy parts line (when natural gas is used for heating while excess heat heating system goes wrong), melting furnace, refining furnace, heat treatment furnace for machining unit and steam boiler. The pollutants are SO2, NOx and smoke dust contained in the smoke generated from the above locations. All the above pollution generating facilities use the most clean energy, natural gas, for burning. Meanwhile, on melting furnace and refining furnace low nitrogen combustion technology such as low NOx burner is applied, and the generated smoke is discharged via chimney.

拟建项目之废气排放部位为硬质合金件生产线的预热炉（余热加热系统故障采用燃天然气加热时）、熔化炉和精炼炉及机加工机组热处理炉和蒸汽锅炉，污染物为以上部位产生的烟气中含有SO2、NOx以及烟尘，以上各产污设备均采用最清洁的能源——天然气为燃料，同时熔化炉和精炼炉采用低NOx烧嘴等低氮燃烧技术，产生的烟气由烟囱排放。

Of or relating to involuntary movement of a body part accompanying voluntary movement of another.

交感的与身体一部位的自觉运动相伴随的另一部位的不自觉运动的，或与之相关的

Careful treatment can decrease the complication rate. 3. Three-dimensional finite element model analysis showed that zygomaticoalveolar crest is the major site sustaining stress, which indicated that the fixation of zygomaticoalveolar crest should be strengthened, if there is some space between zygomaticoalveolar crest and fibula bone, free bone graft can fill the space to rebuild the bony zygomatic process support.

游离腓骨复合组织瓣上颌骨重建的三维有限元分析表明，颧牙槽嵴部位是腓骨瓣上颌骨重建后咀嚼压力的主要受力部位，提示腓骨瓣上颌骨重建时要加强颧牙槽嵴的固定；当上颌骨切除后腓骨与颧牙槽嵴存在间隙时，应尽量采取游离骨块移植，充填间隙，重建骨性颧突支柱。

Print, and aspects of the seihan process is an important process of the mesh camera negatives was, the speed of image at high-profile sites transparent, to take 3.5 MW to 750 MW, 4.5 become positive exposure after dot 3% or more low key parts of the image xiaohei point 0.5 to 1 captured the idea to become dark circle, you must have tried small solid reflective point after desensitising cannot be displayed.

晒版是铜版制版工艺的一个重要工序，它对网目照相的底片要求非常严格，一般要求图像高调部位网点透明，要拍摄到3.5～4.5成为宜，晒版后阳图网点在3成以上，图像低调部位小黑点拍摄到0.5～1成为宜，点子要黑要圆，必须照足细小坚实的反光点，以便版面腐蚀后能显示层次。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。