道

This paper studies the main geometrical parameter such as angle, height, width, stagger and the upper width in dentation and trapezoid flow path, firstly, uses the single-phase numerical simulation of the computational fluid dynamics technique to analyse the influence of different geometrical parameter on discharge coefficient and flow state exponent of drip emitter. Secondly, uses the two-phases numerical simulation of CFD (1% sand content ) to analyse the influence of the above mentioned geometrical parameter on the contribution regulation of sand and anti-clogging performance. Thirdly, uses the PIV （ particle Tracking Velocimetry ） technique which can see the small-scale flow path to observe and test the trajectories and velocities of solid particles in labyrinth flow path, and analyses the basic factors which can influence the movement characteristic of solid particles and the flow state in flow path.

本文以齿形流道、梯形流道为主要研究对象，以流道转角、流道高，流道宽、偏差量及梯形流道上底宽为主要结构参数，首先应用 CFD 单相流数值模拟技术对不同结构参数灌水器流道水力性能进行模拟，分析了不同结构参数对流态指数和流量系数的影响，其次，应用 CFD 两相流（含沙量为1%）数值模拟技术分析了结构参数对含沙量分布规律和抗堵塞性能的影响，然后，应用 PIV 可视化测试方法测试了固体颗粒在流道内运行轨迹及速度，分析了影响固体颗粒运动特性及流道内流体流态的基本因素，最后，对上述流道结构形式通过模具加工及滴灌带试制，进行了标准化测试（ GB/T 17187-1997 农业灌溉设备滴头技术规范和试验方法与 ISO 标准 ISO /TC23 /SC18 /WG5N4短周期堵塞测试程序），测试结果验证了 CFD 模拟结果，并提出了迷宫结构流道灌水器的抗堵塞设计方法。

In this paper, according to the research and application of fishway at home and abroad, and in combination with in-situ research, the construction, development process and main structure types of the fish-passing facilities are detailed introduced, the fishway board type, its corresponding hydraulic characteristics and the general principles of fishway design are listed, the differences of application conditions and the design issues involving in the fishway are analyzed.

通过国内外鱼道研究、应用资料以及现场调研，比较详细地介绍了国内外鱼道设施的建设、发展过程和鱼道结构所包含的主要类型；列出了国内外多个鱼道隔板型式和相应的水力特性；总结了鱼道设计的一般性原则；分析了国内外鱼道过鱼条件和适用情况的差异以及我国鱼道设计中存在的问题等。

In the aspect of shrimp migration test, the finding reports that shrimp would use the porosity filtering to crawl towards upstream when the flow rate is at 0.001cms, and do so on the bottom of the fishway when the flow is even less.

试验结果显示，在水理试验方面，改良后鱼骨型鱼道水位皆比原鱼骨型鱼道高，流量则比原鱼骨型鱼道低，显示多孔隙滤材能有效改善流况；排砂试验方面，泥砂约於时间第30分钟即达到输砂平衡，排砂率在97％以上，残留於鱼道之泥砂为3％以下，证明增设多孔隙滤材并不影响其排砂率；鱼类上溯试验方面，粗首鱲於试验时间内，上溯率达73％以上，皆比原鱼骨型鱼道为高，显示改良后鱼骨型鱼道更适於鱼类上溯；而溪虾上溯试验方面，发现溪虾於流量0.001时，藉由多孔隙滤材向鱼道上游攀爬，再由量更小的情况下，溪虾便由鱼道渠底向上游攀爬。

The deep water deposition means the deposition in the area where the water depth is larger than 30 meters, in which the major sediments are coarse sand and gravel. This kind of deposition is the relic deposition formed by the Pleistocene alluvial-lacustine deposition reworked under modern channel currents actions, and ususally the Holocene acummulation lack in the deep waters. The transitional zone deposition is the deposition between the low tidal level line and the 30 meters isobath, where the sediment types is changeable and the grain sizes are gradually coarsening from the low tidal line to the deep water area. This kind of deposition is developed by the deep water eroded sediments sorting under the transitional zone current action. The different types distributed along the isobath. The tidal flat deposition is the fine sediment deposition on the tidal flat which is flo sedimentation of the silty clay under the tidal flat dynamic action and ususally developed fluid mud on the lower tidal flat. The channel mouth deposition is the deposition in the channel mouth area. According to the sediment types, it includes sand deposition where there are coarse sediments supply and silt deposition where there are only fine sediments surpport.

峡道深水区沉积是指水深大于30米的峡道底部沉积，它以粗颗粒砂砾石沉积为特色，是现代峡道水动力对第四纪海退时发育的冲洪积和坡积物进行改造形成的蚀余沉积，全新世沉积地层往往缺失；峡道过渡带沉积是指水深介于低潮位线至30米水深线之间发育的峡道边坡沉积，该带沉积以沉积物类型多样为特色，自低潮位线至30米水深线，沉积物粒级逐渐变粗，由粉砂质粘土逐渐递变为中粗砂，是峡道深水区沉积物经多次分选沉积而发育的，基本平行于等深线分布的条带状沉积，在岸坡较陡岸段，过渡带下部可发育重力沉积；峡道潮滩沉积是指在低潮线与海岸线之间发育的细颗粒沉积，它是粘性细颗粒泥沙在潮滩动力作用下，发生动水絮凝沉积而形成的粉砂质粘土沉积，在低潮滩可发育浮泥；峡道口门区沉积则是在峡道汇入大海或海湾时，在峡道出口水流影响所及范围的沉积，根据峡道口门区供给泥沙的特性，峡道口门区沉积有粉砂质淤泥沉积和砂质沉积两种类型。

It is thought that the channel bay line evolution processes can be divided into four stages. The first stage is soon of the sea level stable when the bayhead mountines are eroded and developed abrasion geomorphy and the productive materials were transport into the bay deposition by the tidal current and wave current and were reworked into gravel dams. The second stage is characterized by the fluvial output sediments and eroded sediments mixed deposition in channel bay and developed marine accumulation plain and sand riges in the plain under the wave reworked. The third stage developed clay silt marine accumulation plain under the action of the channel current and the wave action is very limited. The fourth stage is marked by human being reclaim which result in the channel bay filled and evoluted into a strait arce coast.

文章认为，峡道海湾的充填经历了四个阶段，第一阶段以峡道海湾湾顶山体在波浪作用下产生的侵蚀物质充填为主，发育了海蚀崖、海蚀洞、海蚀穴等侵蚀地形和湾顶砂砾石堤等堆积地形交替的峡道湾顶地貌，第二阶段以河流输出物质和峡道湾岛屿、礁石侵蚀物质在潮流作用下向峡道湾输运，由潮流和波流共同沉积为特征，发育海积平原，部分粗颗粒泥沙在波浪的改造峡，发育平原沙堤，第三阶段以河流输出物质为主，在涨落潮流搬运下进入峡道和峡道湾沉积，在峡道湾中发育以淤泥质粉砂为主要物质的海积平原，第四阶段以人类围涂造田为标志，加速峡道湾的充填过程，使峡道海湾最终趋于夷平，形成顺直均衡的弧形海岸。

The quality of the silk carpet weaving, the number may be, are: 120, 180, 200, 210, 300, 400, 600, 800, and so on.

真丝地毯的品质按编织的道数而定，主要有：120道、 180道、200道、210道、300道、400道、600道、800道等。

The major works are as follows: 1 The 3-D numerical model of U-sharp flow passages is set up. The single-phase fluid flow and heat transfer are simulated for the U-sharp smooth and rib-roughened flow passages with FLUENT software. Their performance curves, temperature field and velocity vector are obtained and the local heat transfer and flow pressure-drop distribution along flow passage are analyzed. It is revealed that the ribbed flow passages can enhance heat-transfer and make the temperature more uniform, but it increases the pressure-drop to more extent. 2 The influences of diaphragm depth, channel width and board spacing on the performance are investigated.

建立了层叠式蒸发器U形流道的3维湍流模型，用FLUENT软件对尺寸相同的U形光滑流道和肋化流道中单相流体的传热和流动进行了数值模拟，得到了两种流道的传热和阻力性能关系曲线及速度矢量图、温度场，分析了光滑流道和肋化流道的局部换热系数及沿程压降变化，结果表明流道的肋化能有效的增强传热，而且使流体的流动和传热更加均匀，但也较大地增大了阻力。

The simulation results of the cylinder-block model were given in the article, consistent with that of Middlemen"s. It was shown that the block part could improve the uniformity of the flow distribution. The analysis of the flow field of some materials with different power-law factor in the die designed by Mckelvey was close to that of Mckelvey"s. It was shown that the flow distribution was uniform in the die that can producesheets with 1200mm in width. During the analysis the flow channel was divided into several parts to get the details about the fluid flow in each area. A conclusion was drawn after analyzing the influence of the die pressure on the flow distribution, that the higher pressure is good for the output and bad for the uniformity of the distribution. Simulation of the die applying the cylindrical main runner showed the fact that when the cylinder replaced the cone the change of uniformity was trivial. The uniformity of the non-block flow channel was so poor that the block in the proper position of the die channel was necessary. The project of the die for the wider sheet was put forth, and the analysis of the fluid flow in the die was shown.

本文模拟了圆柱管缝隙流模型的三维流动场，得到了与Middlemen结论一致的流动均匀性，并通过模拟直观地展示了采用阻尼块可以改善挤出均匀性的现象；分析了多种幂率指数的流体在Mckelvey等人设计的流道模型中的流动分布，得到了与Mckelvey的分析结果接近的压力降和流量偏差；本文建立了1200mm幅宽机头流道的三维有限元模型，并逐个分析各个区域和多个截面的流动分布状况，由此揭示了1200mm幅宽L-型机头流道内的流北京化工大学硕士学位论文动分布基本均匀，并在分析了机头压力对于挤出流动分布的影响后得出结论：较高的机头压力可以获得较大的产量，但是不利于物料均匀分布；模拟了采用圆柱管主流道时机头流道内的流动分布，得出结论：主流道由圆锥管改为圆柱管时对流动均匀性影响不大，通过设置适当的阻尼仍然可以达到挤出平衡；模拟了两端进料式圆柱管无阻尼流道的流动均匀性后得到结论：两端进料式无阻尼结构的流动均匀性较差，宽机头中仍然有必要设置阻尼块；确定宽幅机头流道的基本方案，并设计了一种宽幅防水卷材挤出机头流道的结构，通过流动模拟表明该种结构的流动均匀性较好；考察了宽幅机头对于不同厚度片材的挤出适应性，得到结论：当生产不同厚度的片材时，阻尼块高度需要调整。

And mining, the mining machinery, the mining slope ramp project are the design main bodies, in mining used advanced low poor has damaged the non-lower column partition to come down the law, will have the huge economic efficiency, the special mining slope ramp project, mainly included the slope ramp position the determination, the slope ramp form choice, the slope ramp cross section specification, the slope ramp slope, slope ramp aspect and so on curve design, slope ramp construction contents.

其中采矿、矿山机械、开采斜坡道工程是设计的主体，采矿中采用了先进的低贫损无底柱分段崩落法，将产生巨大的经济效益，专题开采斜坡道工程，主要包括斜坡道位置的确定、斜坡道形式的选择、斜坡道的断面规格、斜坡道坡度、斜坡道弯道设计、斜坡道施工等方面的内容。

And mining, the mining machinery, the mining slope ramp project are the design main bodies, in mining used advanced low poor has damaged the non-lower column partition to come down the law, will have the huge economic efficiency, the special mining slope ramp project, mainly included the slope ramp position the determination, the slope ramp form choice, the slope ramp cross section specification, the slope ramp slope, slope ramp aspect and so on curve design, slope ramp construction contents.

其中采矿、矿山机械、开采斜坡道工程是设计旳主体，采矿中采用le先进的低贫损无底柱分段崩落法，将产生巨大的经济效益，专题开采斜坡道工程，主要包括斜坡道位置确实定、斜坡道形式的选择、斜坡道的断面规格、斜坡道坡度、斜坡道弯道设计、斜坡道施工等方面的内容。

I didn't watch TV last night, because it .

昨晚我没有看电视，因为电视机坏了。

Since this year, in a lot of villages of Beijing, TV of elevator liquid crystal was removed.

今年以来，在北京的很多小区里，电梯液晶电视被撤了下来。