速度增加
- 与 速度增加 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
While laser welding can improve productivity [1, 2] through increasing penetration depth in the root pass so that the area of groove to be filled can be reduced, technologies have been developed to modify the conventional GMAW (the most widely used process for fill-up) to achieve higher deposition rate so that grooves can be filled in fewer passes or at a higher travel speed.
而激光焊接可以提高生产率[ 1 , 2 ]通过增加渗透深入的根通,使该地区的槽来填补可以降低,技术已经发展到修改常规气体保护焊(最广泛使用的进程填补行动),以实现更高的沉积速率,这样可以填补沟槽较少通行证或在较高的旅行速度。
-
The over-all increase is not due to the velocity constant of the placental transfer but to changes in the relationship of the placental and foetal tissue.
这种增加不是由于胎盘转化速度的持续引起的,而是源自于胎盘和胎儿组织的关系转化。
-
The effect of the tool composition on the friction and wear behavior was investigated,and the morphologies of the rake face and rear face of the tool cutting the steel in air and nitrogen were observed on a scanning electron microscope. It was found that the Al_2O_3/TiB_2 tool was dominated by adhesive and abrasive wear in low speed dry cutting; while in high speed dry cutting,the tool was characterized by oxidation wear. An oxide layer of TiO_2 was formed by way of the oxidation of the reinforcing agent TiB_2 at a very much high cutting temperature, which contributed to greatly reducing the friction coefficient and increasing the antiwear life of the tool.Such a friction-reducing and antiwear behavior of the oxide layer was enhanced with increasing content of TiB_2 in the tool composite. However,the tool showed a relatively poorer wear resistance in N_2 than in air, because N_2 acted to retard the oxidation of the TiB_2 and the formation of the oxide layer on the tool rake face.
结果表明:低速干切削时,Al2O3/TiB2陶瓷刀具的磨损机制主要表现为粘着磨损和磨料磨损;而在高速干切削时,刀具的磨损机制主要表现为氧化磨损,刀具表面经由氧化反应生成具有润滑作用的反应膜而起到固体润滑作用,从而使刀具的耐磨性能提高,随着TiB2含量和切削速度的增加,反应膜的减摩抗磨作用增强;而在切削区通入氮气时,由于刀具表面氧化膜形成受阻,刀具的抗磨能力有所降低。
-
Mass gas-driven growth factor is the increase in the number of gas users and gas prices, State Securities believes that the future of the public gas users add speed limited, gas price increases next year, it is very difficult; but the company is pushing forward gas to natural gas on a certain contribution to revenue growth.
大规模天然气驱动的经济增长因素是用户的天然气和天然气价格的增加,国家证券认为,公众燃气用户未来附加速度有限,天然气价格上涨,明年,这是非常困难,但该公司是推进在一定的贡献,对收入增长的天然气输送到天然气。
-
The results show that increasing gelatin concentration, enhancing emulsion and using mixed emulsifier can decrease the gelatin submicron particle diameter using glutaraldehyde as cross-linking agent.
结果表明,采用戊二醛为固化剂、增加明胶的浓度、提高乳化搅拌速度、使用混合性的乳化剂都有利于降低明胶粒子的粒径此外,对制备工艺进行了优化,并在7000r/min左右高速搅拌的条件下,得到了成球性较好的粒径约为450 nm的明胶亚微米粒子。
-
Replaceable gobos can vibrate up/down,more dynamic,and double way wheel effect,tunable speed
固定图案具有上下抖动功能,增加图案动感。同时具有双向流水功能。且速度可调。
-
It is again repeated at half speed in bars 7 and 8 and the last 2 bars provide the ending.
千万不要尝试在合手的状况下增加速度。
-
Although the US economy is expected to revive gradually in the second half of 2002, the speed of economic recovery remains as a factor of uncertainty.
虽然目前预计美国经济可能在2002年下半年逐步复苏,但是,其复苏的速度仍是不确定因素,&9·11&事件更是增加了这一不确定性。
-
The results show when formations contains a single vertical parallel fracture system, the amplitude of reflected P-wave is more sensitive than velocity for different infillings of vertical fractures; the anisotropy increases as fracture density increasing; the anisotropy of gas-bearing fracture is stronger than the fracture saturated with fluid.
研究结果表明,当地层中含有单组垂直的平行裂隙时,反射P波振幅对垂直裂隙中充填物的敏感性大于速度对裂隙中充填物的敏感性,随着裂隙密度的增加,P波各向异性程度也相应增强,裂隙中含气时,各向异性程度较含饱和水时强。
-
While mixture velocity is higher than 0.566m/s, corresponding to the phase inversion point, a sharp peak in pressure gradient appears.
对于油-气-水三相流动,不同液相含水率下的压力梯度均随着气液相折算速度的增加而增大。
- 推荐网络例句
-
In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.
。但是,在否定句或疑问句里,这种带有"do"的方法表达的效果却没有什么强调的意思。
-
Go down on one's knees;kneel down
屈膝跪下。。。下跪祈祷
-
Nusa lembongan : Bali's sister island, coral and sand beaches, crystal clear water, surfing.
Nusa Dua :豪华度假村,冲浪和潜水,沙滩,水晶般晶莹剔透的水,网络冲浪。