速度

Test and analysis show that, the distribution patterns of the tangent veloctiy fields in the big cone area and the small cone area, which are comprised of para-free vortex and para-forced vortex, are basically identical without a change of the radius of the boundary surface; with the increase of the angle of the small cone, the para-free vortex area decreases and the para-forced vortex area increases, and the emulsifiability of the fluid drips increases with the increase of velocity gradient; the tangent velocity increases with the increase of inlet flow, and the maximum tangent velocities of both the big cone area and the small cone area are 4.94 times of the inlet flow; and the maximum tangent velocity increases with the increase of the split ratio and with the radius of the boundary surface not changed.

试验分析表明，大锥段和小锥段切向速度分布规律基本相同，均由准自由涡和准强制涡构成，分界面半径rm没有变化；随着小锥角θ的增加，准自由涡区缩小，准强制涡区扩大，速度梯度增加会加大液滴的乳化程度；随入口流量增加，切向速度增大，经拟合得出大锥段和小锥段的最大切向速度均为入口流量的4.94倍；分流比加大，分界面半径基本不变，最大切向速度增加。

Therefore the dispersion curves obtained in the field are primarily consisted of the first mode. For a heterogeneous elastic solid consisting of three homogeneous layers whose interlayer has low velocity, the phase velocity V〓 of the first mode will also close up to the Rayleigh wave velocity of the bottom layer when frequency f→OHz, but V〓 of the first mode will close up to the shear wave velocity of the interlayer when f→∞, and there is a cut-off frequency at high frequency region for the first mode and V〓 close up to the compressional velocity of interlayer when interlayer is liquid.

当三层固体介质中存在软夹层时，若f→OHz，则其基阶模式的相速度V〓→V〓（V〓为最底层介质的瑞利波速度）；若f→∞，其基阶模式V〓→V〓（V〓为中间层介质的横波速度）；若三层介质中存在液体夹层，当f→OHz时，基阶模式V〓→V〓，而基阶模式在高频段存在一个截止频率，截止频率处的瑞利波速度V〓→V〓；由此可判定，野外实测的相速度频散曲线不仅有基阶导波模式，同时还应有高阶导波模式波的存在，接收信号中存在模式间的跳跃，因此频散曲线会产生"之"字形现象。

The research of both theories and practices of gridding in the dissertation shows that: Linear interpolation based on triangulation is simple computationally and fast, but its gridding results isn't smooth and its precision is low; Multiquardric method is also simple computationally with high precision and good effect, but its gridding is slow because it is based on global calculation; Minimum curvature method is fast with high precision and good effect, but its gridding quickly degrades over areas with sparse data control when grid spacing smaller than the actual grid spacing is used; Ordinary Kriging method is high-precision, but its gridding is slow because of large calculation; Inverse interpolation is a computationally fast, efficient and robust method with high accuracy and perfect effect, and its gridding results of different gridding orientations are basically identical. Inverse interpolation is suitable for thegridding of geophysical irregular data, especially for large-scale geophysical irregular data.

本文的方法研究和数据试验分析表明：基于三角网的线性插值法计算简单，速度快，但其网格化结果不光滑，精度不够；多元二次函数法计算简单，网格化精度高，效果良好，但它是基于全局计算的，计算速度较慢；最小曲率法计算速度快，网格化精度高，效果良好，但其在稀疏控制点的网格化容易出现振荡现象；普通克里格法网格化精度高，效果良好，但其计算量较大，一般计算速度慢；反插值法网格化计算稳定，速度快，精度高，效果好，而且在网格化方向不同的情况下其网格化精度效果都达到基本一致，适合于地球物理不规则分布数据的网格化，特别是大规模地球物理不规则分布数据的网格化。

It carries on the real-time examination to bicycle's speed whichused the examination and transformation technology, microcomputercontrol and connection technology and digital circuit technology.And the installment will compare the measurable speed with the safespeed which is input by the keyboard. If the measurable speed isfaster than the restricted speed, it will actuate the buzzer towarn.

该装置应用检测与转换技术、微机控制与接口技术、数字电路技术等知识，对自行车的速度进行实时检测，并将这个速度与预先用键盘输入设置好的安全速度相比较，如果速度超过了安全速度的界限，则蜂鸣器自动报警。

An S-shape acceleration/deceleration control model is developed by summation progression and the corner of two conjoint lines is adopted as a parametric variable to control the feedrate through the inflexion of two lines. Based on these, interpolation process is divided into two steps: interpolation pretreatment and interpolation point calculation. Feedrate planning is accomplished in the pretreatment step. Interpolation point calculating only depends on the real-time feedrate and the direction vector of the line.

该算法以级数求和的方法推导了S型加减速控制模型，并以小线段夹角为参变量控制拐点通过速度建立了小线段速度衔接模型，在此基础上，算法将插补过程分解为插补预处理及插补点计算两个步骤，预处理中对小线段进行速度规划并设计了线段速度的递推处理方法，插补点仅需根据当前速度及线段方向向量即可求出。

To analyze the pseudo phenomena caused by migration velocity error, the paper firstly studied the depth error between post-stack migration and prestack migration caused by same velocity error, and found the depth error was only relative to velocity error and had no direct matter with methods of depth migration (post-stack migration or prestack migration). Then the paper did numerical simulation of a complex lenticular body model with wave-equation modeling and migration, and found that the velocity error could not only induce depth error, but also could change the modality of construction and the event of subjacent layers. Furthermore, it could change the frequency of reflective event. They are the pseudo phenomena caused by migration.

从分析偏移速度误差带来的各种假象出发，本文首先对比分析了速度误差对叠后深度偏移和叠前深度偏移的影响，发现偏移剖面的深度误差仅与速度模型的误差有关系，与具体的偏移方法没有直接的关系；然后对一个复杂的透镜体模型进行了波动方程叠后正演和偏移计算，详细地讨论了不同的速度误差带来的各种假象，发现速度误差不仅会带来深度误差，而且会造成构造体的形态变化，下覆地层同向轴的扭曲，还可能引起地层同向轴的频率发生变化，给资料解释带来一定的假象。

Under a fixed model of chromospheric flare, we investigate the influences of Hα and CaIIK line profilles on various velocity distributions from semiempirical view. The results show that: Hα line is very sensitive to the velocity in upper chromosphere; the profile of CaIIK line have responses to velocity in any layer of chromosphere, but the degree of CaIIK line asymmetry is much weaker than that of Hα and can be ignored if velocity is as small as 10km/s; chromospheric condensation in lower part of transition region have strong influence on Hα line but contrary to CaIIK line, the typical characteristic of H line effected by chromospheric condensation in transition region is reversed blue asymmetry, i.e. the intensity of blue peak is stronger than that of red peak; the stronger the chromosphoric condensation is, the more obvious the Hα line asymmetry appears; and so on.

在确定的大气模型下，从半经验角度系统地研究了大气各个层次的速度场和运动结构对Hα和CaⅡK谱线轮廓的影响，得到；Hα线对色球上部速度场敏感，而对色球下部和温度极小区附近速度场不敏感；CaⅡK对整个色球速度场均有反应，但不对称性较Hα弱，且速度小于10km/s时不对称性很不明显；CaⅡK受过渡区色球凝聚的影响较弱，而Hα对色球凝聚十分敏感；色球凝聚影响Hα轮廓的典型特征是呈反转结构的兰不对称性，即兰峰强于红峰；色球凝聚越强，Hα不对称性也越显著：等。

The result makes clear: EThe tensile strength of TFE film increases somewhat along with the addition of drawing speed, and rupture outspread rate reduces;ETFE to succumb filmily somewhat along with the addition of drawing speed the addition that intensity follows drawing rate and increase somewhat, but the 2nd succumb intensity increases not big;ETFE to succumb filmily meet an emergency follows drawing rate increase somewhat, the 2nd succumb the amount of tangent and stretch model that meet an emergency reduces;ETFE film somewhat and model of the 2nd flexibility measure those who follow drawing rate to increase show downtrend, quantity of secant flexibility model and quantity of the 3rd stretch model do not have apparent change.

结果表明：ETFE薄膜的抗拉强度随拉伸速度的增加略有增加，而断裂延伸率随拉伸速度的增加略有减小；ETFE薄膜的屈服强度随拉伸速度的增加而有所增加，但第二屈服强度增加不大；ETFE薄膜的屈服应变随拉伸速度的增加略有增加，第二屈服应变则略有减少；ETFE薄膜的切线弹性模量以及第二弹性模量随拉伸速度的增加呈下降趋向，割线弹性模量和第三弹性模量则没有明显的变化。

The biomechanical tests showed that two kinds of artificial bones had not significant difference on compressive strength and Young\'s modulus(P＞0.05),while the flexural strength of nano-nacre artificial bone was less than the control group(P＜0.05).3.The results of CCK-8 showed that the difference were not significant in each group,the proliferation of osteoblast reached the peak at the 5th day;7 days after being co-cultured,the total protein content of study group was higher than control group and blank group(P＜0.05),while the difference between control group and blank group was not significantP＞0.05The difference of alkaline phosphatase activities among three groups was not significant(P＞0.05The SEM view showed that osteoblast attached and grew well in two kinds of artificial bone.4.X-ray photography showed that two kinds of powder started to degrade in 2 weeks;this phenomenon became more appear in 4 weeks,nano-nacre powder degraded faster than micron-nacre powder,while the hole shadow was easy to be found;in 8 weeks,all the femoral holes recovered and returned to normal bone mineral density in all groups.Analysis of tetracycline fluorescent double marks in the hard tissue grinding slices indicated that new bone grew fastest around the bone defect area in study group,while most slowly in blank groupP＜0.05 SEM(scanning electron microscope observation showed that nano-nacre powder degraded more quickly.The same result can be found through the demineralized sections morphometric analysis,and both of the composite artificial bones made from those two kinds of nacre powder had the good connection with the adjacent tissue in rats body without apparent inflammatory response.5.X-ray photography showed that rabbit\'s bone defects healed faster in study group since NNAB implanted than in control group since MNAB implanted.At 24 weeks after operation,bone density in radial defects had nearly accessed to the normal area,while lower in control group,and turned up nonunion in blank group;The checking of BMD showed that results in study group were higher than those in control group at 8,16 and 24 week(P＜0.05), and the difference between the BMD values in study group at 24 week and those in blank group was not significant(P＞0.05).The gross specimens showed satisfactory histocompatibility both in study group and in control group,with bone tissue growing from two sides into the center of implanted materials; Normal slices in HE stain and hard tissue grinding slices in Stevenel\'s blue/Van Geison\'s picro-fuchsin stain showed that the bone growth tendency was better in study group than that in control group,and the medullary cavity had been penetrated to the implanted materials in study group at 24 week;Analysis of tetracycline fluorescent double marks in the hard tissue grinding slices indicated that new bone in both groups grew fastest 8 weeks after surgery,while slow down at 16 week.

纳米珍珠层/消旋聚乳酸复合人工骨与微米珍珠层/消旋聚乳酸复合人工骨分别与成骨细胞共培养后，其各时间点CCK-8法检测值与空白对照无显著差异(P＞0.05)，成骨细胞均在第5天达到增殖高峰期；培养7天后，实验组细胞蛋白含量高于对照组及空白组(P＜0.05)，后两者之间则无显著差异P＞0.05碱性磷酸酶活性在三组间均无显著差异(P＞0.05电镜下可见成骨细胞在两种人工骨上都有良好生长贴附能力。4.X-ray显示两种粉体在大鼠股骨骨洞植入第2周时都开始出现了降解，第4周时更为明显，纳米珍珠层粉较之微米珍珠层粉降解更快，而空白对照组骨洞阴影仍可见，至8周时，则所有组骨洞均己闭合修复，X-ray下已不可见原钻孔痕迹，恢复正常骨质密度；硬组织磨片四环素荧光双标记结果显示纳米珍珠层粉植入组较其余两组在骨缺损区周围新骨生长速度更快，空白组速度最慢P＜0.05电镜观察及常规脱钙切片亦可见到纳米粉体降解较快；由以上两种原材料制得的纳米珍珠层/消旋聚乳酸复合人工骨与微米珍珠层/消旋聚乳酸复合人工骨在大鼠体内均与周围组织结合良好，无明显炎症反应。5.X-ray显示纳米珍珠层/消旋聚乳酸复合人工骨植入兔桡骨缺损区后其骨愈合速度较对照组微米珍珠层/消旋聚乳酸复合人工骨植入的快，至植入术后24周，实验组骨缺损区接近正常骨密度，对照组骨缺损区密度较低，空白组则呈现骨不连状态；骨密度测量结果显示术后8周、16周、24周实验组的骨密度值高于对照组(P＜0.05，24周实验组的骨密度值与术前所测得的正常值无显著性差异P＞0.05动物取材大体所见均显示组织相容性良好，骨组织逐渐由植入材料两端向中央生长；常规切片HE染色及硬组织磨片Stevenel\'s blue/Van Geison\'s picro-fuchsin联合染色均可见实验组骨缺损区长势优于对照组，至术后24周，实验组骨髓腔与材料已呈相交通状；硬组织磨片荧光显微镜下观察，两组材料在术后8周处于骨生长最快速时期，16周时速度开始减慢，术后4、8、16周时实验组的新骨生长速度均较对照组的快

Considering the limits of RDSS in active positioning mode,such as poor security,limited capacity,and inability to continuously provide position,velocity and attitude outputs,a technique of tightly coupled RDSS /SINS integrated navigation system is proposed for land vehicles by utilizing the time differenced carrier phase of 3 geostatic satellites.

针对北斗系统有源定位方式保密性差、用户数目有限，不能提供连续的位置、速度、姿态信息的问题，提出利用北斗系统3颗地球静止卫星的载波相位时间差分信息，与车载捷联惯导构成紧组合导航系统，通过扩展卡尔曼滤波器估计并修正惯导系统的速度误差；引入载体的侧向和天向速度约束，改善了速度估计精度；结合北斗系统的伪距信息，消除了长航时条件下位置误差的积累；推导了滤波器观测方程，对组合导航滤波器进行了设计；通过车载实验进行了验证，实验结果表明，速度误差和位置误差的积累受到了有效地抑制，精度满足陆地战车导航的要求。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。