退回

Just let the air machine fill up the bounce house's interior with adequate amount of air.

只是让空气机填补退回室内装修有足够数量的空气。

This from modern guns, artillery and armored train was composed of defeat invading army had to return June 18 Yangcun, in the pursuit of the Boxer, thezai bai back to Tianjin West Railway Station.

这支由现代化的枪支、火炮和装甲列车组成的侵略军遭到惨败，不得不于6月18日退回杨村，在义和团的追击下，再败回天津西站。

They lost 26 casualties (8 killed) to small arms fire before they abandoned the effort, falling back to the second assault parallel line.

他们在放弃努力前的小部队交火中，损失了26人(8人阵亡)，英军退回到第二条与突击战线平行的战壕。

Fact Three: When the lead goose gets tired, it rotates back into the formation and another goose flies at the point position.

事实三：当领头雁疲劳的时候，它会退回到队列中，然后另一只大雁会轮换它，飞到领头的位置。

The moving ball will hit the ball at rest and push it away, but it will also be pushed back by the latter.

运动的球会击中静止的球，并将它推走，同时前一个运动的球也会向后退回。

Bank return receipt to cashier, and attach it with the AP voucher

出纳收到银行退回的回单，并粘贴于凭证后。

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

The Bid Bond of a successful tenderer will be refunded upon furnishing of the required Performance Bond.

中标人的投标保证金在缴纳了必要的履约保证金后退回。

There is the suspicious and tentative withdrawal of a door before the unhappy book agent or peddler.

当你面对上门推销的书商或者小贩时，你把门打开了，但又带着猜疑和犹豫退回了门内。

When the spindle box cutter left Move right back to the workpiece, the rotary table 90 degrees, and then the left spindle box again.

当主轴箱右移退回到刀具离开工件后，工作台回转90度，然后主轴箱再次左移。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。