迭代法

For the characteristic of ring permanent magnet torque motor used in direct drive numerical control round table suffering from the effect of load disturbances and parameter variations, the H∞ controller design methodology without the orthogonality assumptions is combined with m-K iteration in m synthesis to design a m-H∞ speed controller in this paper.

针对直接驱动数控转台用环形永磁力矩电机易受负载扰动及参数变化影响的特点，将去除正交性假设的H∞控制器设计方法与m综合中的m-K迭代法相结合，设计了一个m-H∞速度控制器。

Msmodel is formulated with the relative displacement and the contact press direCtiyin the orthogonal coordinate syStem, without introducing the slip angle asvariable and transforming the variab1e to the polar coordinate system.

在工程实际中得到大量应用的二维摩擦接触问题迭代法，贴近力学直观，无须引入额外变量，无须计算导数矩阵，被工程界所熟悉。

With Overrelaxation Iterative Method for second-order partial differential equations.

用超松弛迭代法求解二阶偏微分方程。

With Overrelaxation Iterative Method for second-order partial differenti...

用超松弛迭代法求解二阶偏微分方程。得到电场的分布。

A fourth-order compact finite difference alternating-direction-implicit algorithm is proposed for solving the unsteady-state Navier-Stokes equations of fluid flow and heat transfer using the streamfunction-vorticity formulation. Point-successive overtaxation iteration is used to achieve the steady solutions.

本文构造了求解二维非定常涡量流函数形式Navier-Stokes方程组的一种四阶紧致交错方向隐式差分算法，对包括能量方程在内的离散化方程组采用逐次超松驰迭代法求得稳定解，求解了二维非定常粘性不可压缩流体的流动与传热问题。

Using PH linearization ,the nonlinear partial differential equation was transformed into linear partial differential equation,and then,by introducing a complex function,it was further transformed into a set of two linear differential equations.

应用 PH线性化方法，将非线性偏微分方程转化为线性偏微分方程，引入复函数将复常数偏微分方程变为两个线性实常数微分方程组，并采用小参数迭代法进行求解，近似求得了螺旋槽内气体动压分布的解析解。

In this chapter, we show that Perron complements of N_0~2-matrices are N_0~2-matrices. We also demonstrate the Perron complements of inverse N_0~1-matrices are inverse N_0~1-matrices with certain restriction.

第四章研究非严格广义双对角占优矩阵的Schur余的性质，对角占优矩阵是数值计算中经常遇到的一类矩阵，它的Schur余可应用于迭代法的构造。

This approach uses the geometric features and radiation features of the road, according to the small amount seed points given by the user, each point in the road centerline can be gotten. Then an adaptive gray template is used to adjust each point in the road centerline. Finally, least square method and Newton iteration method are adapted to each point in the road centerline to fit a polygonal line.

该方法利用道路地物的几何特征和辐射特征，根据用户提供的少量道路种子点，利用自适应灰度模板对道路中心线上的每个点进行调整，最后采用最小二乘算法和牛顿迭代法对调整后的道路中心线上的每个点进行拟合，以此获得趋近于道路中心线的最佳折线。

Firstly, an Iterative Closest Point algorithm is applied for coarse registration. Secondly, gradient feature is extracted from image. Based on the principle of projective transformation, the fine registration is performed by finding the maximum CT gradient projections.

首先基于一种最近点迭代法进行快速粗配准；然后提取图像的梯度特征，根据投影变换原理，采用寻找具有CT最大梯度投影位置的方法进行精配准。

Based on the concept of the non-proportional damping which may be divided into the proportional part for dissipation of energy and the nonproportional part for transformation of energy, a new modal superposition pseudo-force method is presented if the approximate decoupling method is not suitable. In this method the coupled modal equations are solved by iteration in which the coupling terms are treated as pseudo-force and set to the right side of the equations.

在不能进行近似解耦分析时，基于非比例阻尼可分为耗散能量的比例部分和转换能量的非比例部分这种概念，建立了一种拟力实模态叠加法，即把正则化的耦合模态方程中代表非比例阻尼部分的耦合项作为虚力，放到方程的右端，再运用迭代法求解。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。