连杆运动

To reduction gear, the design calculation and necessary strength check of gearwheel and gear shaft have been accomplished.

其中对乳化液泵的传动端采用了曲柄连杆机构，并对曲轴、连杆、十字头及其配件进行了结构设计，运动和动力分析，必要的强度刚度校核；对乳化液泵液力端的柱塞选择和和密封，进行了必要说明；对减速机进行了齿轮和齿轮轴设计计算和强度校核。

Neutral document is produced in the ANSYS software which has been applied to the ADAMS environment; the application of neutral document realized the hard and soft coupling kinematics analysis of link motion gear, the rule that when the link motion gear comes to the limiting position, movement will be change suddenly has been confirmed.

在ANSYS软件环境中生成了可应用于ADAMS的中性文件，应用中性文件实现了连杆机构的刚柔耦合运动学分析，验证了连杆机构在极限位置时，运动发生突变的规律。

A combination of VB6.0 and the software of dynamics simulation analysis of mechanical system ADAMS complete the dummy test platform design, the modeling as well as the determination of movement parameter; realize the collection of the design of link motion gear, the parameter modeling, the kinematics analysis and dynamics analysis of machine as an incorporate experiment platform.

结合VB6.0语言和机械系统动力学仿真分析软件ADAMS完成了虚拟试验台的设计、建模以及运动参数的测定，实现了集连杆机构设计、参数化建模、机构运动学分析和动力学分析为一体的连杆机构综合实验台。

A mechanism for performing path synthesis is designed to guide one point on a moving rigid body such that it passes through a specified sequence of points on a path.

轨迹综合机构是指能使连杆上某点沿着某一给定轨迹运动的平面连杆机构综合。

Thirdly , a conclusion has been settled down in this dissertation: Because the shaft inertial force vector do not pass the center of the rotating center of the system, there is a moment generated by the shaft inertial force and the counterforce of the cylinder wall to counterbalance the pressure which is imposed by the piston, so, it is important to consider the tortile effect on the flexible supporting component of the balancing machine dedicated to motorcycle crank set, which is originated by the moment.

第三：得到了一个结论：在设计制作曲柄连杆机构动平衡测试装置时，必须考虑这一受力情况，即连杆在作平面运动时，其自身的惯性力与汽缸对活塞的反作用力二者之间形成的力偶将会对弹性支承元件产生扭矩的作用。

In the paper, the common expression of the non-uniform load shareing factor was deduced, and a function parameter--forc-arm factor and the concept of ideal centre position were presented and their solutions were given, which makes it possible that the dimensions and the capability of load equilibrium of the mechanism could be determined. The criteria of optimum load balancing mechanisms selection were set up with consideration of the effects of frictions and turning pair clearances.

本文通过对平面连杆式均载机构的功能指标—载荷不均匀系数的推导和分析，提出了力臂系数、理想中心位置这样一些能反映均载机构功能与运动结构关系的参数与概念，并给出其求解方法，它们还可以用来确定平面连杆式均载机构各构件的最佳长度尺寸。

The multi- connecting rods press is one kind new press which taking the multi- linkmotion gear as the operating mechanism.The slide has the obviously comes back promptly kinematics the characteristic.In work sector,The slide"s speed is steady, and is lower than the crank press greatly, this is advantageous to enhance quality of the big distorts stretch. At the same time it reduces the impact between the molds and lengthen the mold"s service life.

多连杆压力机是一种以多连杆机构为工作机构的新型压力机，滑块具有明显的急回运动特性，在工作区间，滑块速度平稳，并且大大低于曲柄压力机，这有利于提高变形较大的拉伸件的质量，同时减少模具间的冲击，延长模具使用寿命。

Adequate comparison and introduction is made on the structure and moving mechanism of typical gates applied in water and power works such as curve pedestal gate, fix double_supporting point gate and fix wheel link involute gate.

对目前水电工程常用的曲线支座式、定轮双支点式、定轮连杆式渐开型闸门结构型式及运动原理进行了充分的比较和说明，并结合工程实例，对定轮连杆式渐开型闸门的设计和计算进行了详细的介绍。

Connecting rod in the movement of inertia and centrifugal force considerable power in the working conditions for connecting rod with high intensity, light weight, although good, strong resilience, life-long characteristics.

连杆在运动中形成的惯性力和离心力相当大，在这样的工作条件下，要求连杆有强度高、重量轻、刚性好、韧性强、使用寿命长的特点。

Connectingrod in the movement of inertia and centrifugal force considerablepower in the working conditions for connecting rod with highintensity, light weight, although good, strong resilience,life-long characteristics.

连杆在运动中形成的惯性力和离心力相当大，在这样的工作条件下，要求连杆有强度高、重量轻、刚性好、韧性强、使用寿命长的特点。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。