连杆

Then the paper analyses the vector kinematics equation of the speed, and on this foundation, makes use of the software package of Simulink to carry on kinematic simulation to the mechanism, the kinematic regulation of slip block and linkages provide the basis for the design and manufacture and application of the mechanism.

对其速度运动学方程进行分析，并在此基础上利用MATLAB/Simulink软件包对该机构进行运动学仿真，通过仿真可得到滑块和连杆的运动规律，为机构的设计、制造和应用提供了依据。

Lower pairs include revolute or pin connections—for example, a shaft in a bearing or the wrist pin joining a piston and connecting rod. Both elements joined by the pin may be considered to have the same motion at the pin center if clearance is neglected .

低副包括外卷或销钉连接——如在轴承内的或对接活塞或连杆的活塞销的轴，如果不考虑空隙的话，由销钉对接的两种部件都可以被认为在销钉中心具有同样的运动。

Because of the connecting rod is one of dyadic engine of piston and main compression engine part, whose larger end hole and crank shaft link up , the small head hole links up by the wrist pin and the piston , whose effect is that the piston gas pressure is transmitted to the crank shaft , collect crank shaft gas in driving but setting a piston in motion to compress a cylinder. the intensity is high.

因为连杆是活塞式发动机和压缩机的主要零件之一，其大头孔与曲轴连接，小头孔通过活塞销与活塞连接，其作用是将活塞的气体压力传送给曲轴，又收曲轴驱动而带动活塞压缩汽缸中的气体。

Generally we used traditional analogism and the improvising method to design them. In this paper, the finite element analysis method is applied. Firstly, the static analysis of the device is carried out and the reaction forces at the joints are calculated.

本文基于有限元分析理论，首先研究装载机的工作装置的静力分析问题，根据装载机工作装置受力最大时铲斗所受的外力，以及装载机工作装置的位置分析，求得装载机工作装置中摇臂和连杆零件各铰接点处所受的力。

Experimental results indicate that the asway mechanism can provide a stable and reliable working state and its positioning accuracy reaches 0.02 mm under the depth of fracture splitting notch in (0.5±0.05)mm.

试验结果表明，在合适的工艺参数条件下，摆头机构的定位精度达到±0.02mm，且工作稳定、可靠，连杆裂解槽槽深均为(0.5±0.05)mm。

The simulation results show that the improved asway mechanism can complete the asway process in 0.4 s with a more accurate asway angle, which proves that the servo electromotor driven asway mechanism is reasonable and can provide a reliable theoretic basis for optimizing the structure of the laser cutting fracture splitting notch machine.

仿真结果表明，改进后的摆头机构可在0.4s内完成摆头动作，且摆动角度调整方便，说明改进后的摆动机构是较理想的激光头摆动方案，可为连杆初始裂解槽激光加工主机结构优化提供可靠的理论依据。

Main products are piston, bettery, carburator assy, flashier, ignition switch, shock absorber, fuel cock, steering lock, starting coil, clutch cable, speedmeter cable, gear shaft, kick shaft, con-rod, engine block, chain, fuel tank, bulb, gear, pointer, water pump, relay, bearing, rear hub, clutch firber, sprocket, lever assy, back mirror, etc.

主导产品：活塞及活塞环，电瓶，化油器，闪光器，点火开关，减震器，油开关，车头锁，点火线圈，导线，齿轮，连杆，汽缸，链条，油箱盖，灯泡，转向灯，水泵，继电器，轴承，轮股，离合器片，链轮，把手，后视镜等我们生产和销售各种摩托车和汽车配件，并且在不断地开发新产品。

Combining Newton two state model with step function,a u nified dynamic model between separation and collision process for the linkage me chanism with clearance connections,and with variable rotating speed of the cran k was developed in the paper.

将阶跃函数与牛顿二状态相结合，考虑曲柄非匀速运转，对含间隙平面连杆机构的副间分离与碰撞过程建立了动力学统一模型，利用该模型，引入粘弹性阻尼被动控制技术，通过算例分析了被动控制的效果。

Mainly engaged in a new type of lateral pressure without cycloidal gear linkage within the internal combustion engine research and development of economic management and software development.

主要从事新型无侧压无连杆内摆线行星齿轮内燃机的研制开发和经济管理软件的开发。

Crank bearing is the key component of crank connecting rod mechanism of emulsion pump and the damageable part during power transmission.

曲柄轴承作为乳化液泵曲柄连杆机构的关键部件，也是动力传递过程中极易损坏的薄弱环节，曲柄轴承的磨损失效是高压大流量乳化液泵的主要失效形式。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新