连接角

Based on the Banyan construction and the PLC technology, and with the intersection linking angle of 30 degree, we fabricated a strictly nonblocking silica waveguide 4×4 matrix optical switch.

设计了基于Banyan网络的4×4光开关，连接波导交叉角为30°。

The source of the MESFET 30 is connected to the ground line 22 via an RF choke 34 which shunts the capacitor C. A dc blocking capacitor 32 is also included in the feedback path.

该消息人士30日的场效应管连接到地面线22日通过的RF扼流圈34其中分流电容角直流阻挡电容器32也包含在反馈路径。

If you set to connect after the show, and you will also discover the bottom-right corner of the screen icon in the flash card

如果你设定为连接后显示状态，你还会发现屏幕右下角的网卡图标在闪

As the main conjunctive mode of the steel structure, high-strengthened hexangular bolt joint auxiliary has got widely used in production.

高强度大六角螺栓连接副作为钢结构的主要连接方式，在生产中得到了广泛的应用。

Methods A wet hip joint's sample from corpse was scaned by CT and all images of every cross-section hip joint's layer was obtained, and an hip joint's model was contructed with Unigraphics NX 2.0 and Solid Works 2006 SP 0.0 software. The models were assembled when simulated total hip arthroplasty after total hip joint prosthetic and ischiofemoral ligament model had been constructured. Analysis was done on von Mises stress distribution and amount of total hip component when simulated seated leg-crossing manuver. The bone and metal components were meshed as rigid bodies, composed of three-dimensional, all-quadrilateral rigid body elements, and hip joint capsule ligament was fully three-dimensional, hexahedral continuum elements representations. Results The current form of this ischiofemoral ligament's reconstruction finite element model provided for multi-body contact, large displacement interfacial sliding, large deformation capsule ligament representation, and clearly reflected the real ischiofemoral ligansent's anatomy and biomechanical behavior. The maximum on Mises stresses at the joint interface was more than that fur an otherwise identical hardware-only construct.

选择成人尸体髋关节行CT成像得到髋关节每层横截面图像，提取边界坐标，利用有限元分析软件Unigraphics NX 2.0和Solid-Works 2006 SP0.0构建出髋关节三维有限元模型及人工髋关节假体，并模拟全髋置换术进行装配，将坐股韧带按其术中重建位置进行构建骨骼与金属模型采用三维十节点四面体实体单元进行网格划分，关节囊六面体连接单元划分，模拟坐位腿交叉动作载荷获取假体撞击过程的角活动度和相应的von Mises应力分布情况结果所构建的多体连接、大界面划移、大变形的坐股韧带重建有限元模型，客观反映坐股韧带真实解剖形态及生物力学行为，增加坐股韧带重建的模型其关节面的最大主应力值大于仅有金属的模型。

Upon the addition of CdS into the GeS2-Ga2S3 system, the number of the metal-metal bonds and edge-shared GaS4/2 tetrahedra decreases, resulting in the formation of corner-shared tetrahedra with non-bridging sulfurs.

随着CdS逐渐加入到GeS_2-Ga_2S_3玻璃中，金属-金属键和共边连接的GaS_(4／2)四面体逐渐减少，导致相应共角连接四面体和非桥硫的出现和增加。

The machine is specialized in production of hi-grad alu door sand windows , and is suitable to connection of 90 angle structure of alu doors and window .

高档铝门窗生产专用设备，适用于角码结构型铝门窗90°角连接

Hose thread connection, angle pattern

BD2C -通径DN20可锻铸铁管连接端口 x DN20软管螺纹连接端口，角式

Special localized cutting communication with the customer; 2.5 If not available notched hole diameter less than 60 mm hole, can be used to be relatively enlarger for the opening; After opening 2.6 backplane approach, starting with the opening negative, positive exposed bit sharp, nated from the positive control (both sides maintain collapse teeth); 3 connected corner of the corner of the 3.1 connection method, identify three Kok code on the middle and lower (50 mm poured from top to bottom. Another try a) 3:00 even in the corner of the counter and cross wooden cabinet on the sideboard; 3.2 corner of the Outer Limits with a shutter-ping; 3.3 In accordance with the drawings corner of the size, will have a fixed angle of the black reinforce the lower corner with 3:00 counters even

特殊局部地方的切割必须与客户沟通； 2.5如割口不大可用圆孔、直径小于60mm孔，可用相对应的扩孔器进行开孔； 2.6后背板开孔方法，先从反面开孔，正面露出钻头尖时，再从正面往里操作； 3 转角条的连接 3.1转角条的连接方法是，找出三个角码，上中下（上下50毫米往里，另居中一个）三点连在与转角柜交叉柜体的侧板上； 3.2转角条的外沿与门板一平； 3.3按照图纸转角条尺寸，将已固定的转角条用黑钉上中下三点与转角柜连

Aluminum alloy worktable, has profiles framework, the above has units plate,two sides and back having hoarding,in frontof the framework,there are doors, drawers, etc., the side of the profiles, along the profiles' direction have trough-shaped cross section, the framework of the vertical connections between profiles useful screw connected straight dihedral angle-shaped corner connector and square plate-shaped nut.

优点advantages；铝合金工作台，有型材框架，框架的上面有台板，两侧和背面可有围板，框架前面有柜门、抽屉等，型材的侧面上、沿型材长度方向有内腔横截面是工字型槽，框架垂直连接的型材间有用螺钉相连的直二面角形的弯角连接件和方板形螺母。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。