连接体

ZL03 2 354312.The innovations include: automatic self-closing and reliably sealed valve structure: the design of duplex valve clack with pilot valve to tackle the problem of reverse seal structured valve being difficult to be opened; an automatic drain control device to automatically drain the remaining water from the hydrant; protective plate provided between the hydrant body and the valve block to serve as a connection between the hydrant body and the valve block, which is the first one to be damaged when the ground hydrant is clashed, and prevent pulling-off of the whole above-ground part of the fire hydrant, so as to properly protect the main parts from any damage. The self-closing and reliably sealed valve now prevents drain of water, and only the damaged protective plate is needed to be replaced before immediate re-operation. Thus the repair work after clashing is very easy and simple.

其创新点为：具有能自动关闭并可靠密封的阀门结构：采用有先导阀复式结构阀瓣设计，解决反向密封结构阀门开启沉重费力的难题；设计自控排水装置，能自动排除栓体内余水；在栓体和阀体之间设计撞裂板，它既起到连接栓体和阀体的中介作用，又可在地上消火栓被撞击时率先破裂毁坏，并使露出地面的栓体不见整体脱落，有效保护各主体部件的完好无损，而此时阀门的自闭式结构可靠密封阀门阻止水源外泄，修复时只需更换损坏的撞裂板即可立即复位投入使用，使被撞后的修复工作变得十分轻松简便。

We attached for the first time -NOBIN to Frechet-type dendron units. The syntheses of 16 kinds of dendrimer-based NOBIN Schiff-base ligands were achieved in a straightforward manner by simple condensation of -NOBIN with the corresponding salicylicaldehyde derivatives, of which 12 belong to the dendritic Schiff-base ligands and 4 belong to the non-dendritic Schiff-base ligands.

通过手性拆分获得了光学纯化合物NOBIN，首次将NOBIN手性单元连接到树枝状大分子中去，设计合成了四个系列16种新的NOBIN衍生的希夫碱三齿手性配体，其中4种为非树枝状手性希夫碱配体，12种为树枝状手性希夫碱配体。

Curtain plate stainless steel plate, spray nozzle for the spray nozzle to capture, exhaust fan with explosion-proof fan.3, chamber body assembly plate connection between the use of bolts, installation, removal, fast and convenient.4, configuration, special explosion-proof spray room lighting, interior lighting sufficient light.5 mist treatment with water curtain, shower folding capture plus maze can efficiently remove the paint mist.6, circulation pump with an area of small, simple installation and pipeline pumps.7, Room δ1.5mm steel and steel body is made of.8, dust chamber body is made of EPS board, has entered out.9, water curtain spray booth technical parametersNo Item ParametersA flow rate (m3 / h) 90002 Power 43 pump power 34 open wind speed 0.6-0.75 Compressed air consumption (m3/min) 0.36 lamp illumination 400Z-7 nozzle8 Painting Room: Dimensions 2500 × 2400 × 26009 Dust Room: Dimensions 2500 × 1800 × 3400Note: Manual spray system uses 你好gh-quality brand-name products in Taiwan.6, leveling RoomLeveling effect of room to spray paint surface after the paint on the share level, and to a number of solvent evaporation in order to prevent baking too quickly appeared in the film pinhole.1, Room body is made of welded steel and steel plate.2, chamber body wall windows with transparent glass observation and maintenance of the door.3, chamber body with the top emission device, keeping indoor air fresh.4, room spray processing site in vivo, uniform color, elegant appearance.3, the consolidated statementa, baking oven is designed to bridge Road.

没有碰到水帘的漆雾由水帘下部进入喷漆室的后部，由喷嘴喷出的水雾冲洗、迷宫折板过滤及折板上的喷淋系统三次过滤后，废气经风机排至大气中，布局特点如次：一、设置双工位水帘喷漆室。二、槽体采用型钢及Q235钢板制作，板厚4mm。水帘板为不锈钢板，喷淋捕捉喷嘴为雾化喷嘴，抽风机采用防爆型风机。3、室体拼装板之间采用螺栓连接、安装、拆卸、迅速，便捷。四、配置喷漆室专用防爆照明，内部采光充足、明亮。5、漆雾处理采用水帘、喷淋捕捉加迷宫折板，可高效去除漆雾。6、轮回泵采用占地少、安装简略的管道泵。7、室体采用δ1.5mm钢板与型钢制作而成。八、防尘室体采用EPS板制成，设有出进门。9、水帘喷漆室技术参数序号项目参数1 处理风量（m3/h） 90002 功率 43 水泵功率 34 开口风速 0.6-0.75 压缩空气耗量（m3/min） 0.36 照明灯照度 4007 喷嘴 Z型8 喷漆室：外形尺寸 2500×2400×26009 防尘室：外形尺寸 2500×1800×3400注：手动喷漆系统采用台湾优质名牌产品。六、流平室流平室的作用是使喷漆后喷在工件表面上的漆铺平，并使溶剂挥发一些，以防止烘烤过快而在漆膜上浮现针孔。一、室体采用型钢与钢板焊制而成。

"In chelates, the ligand attaches at more than one point, sharing more than one electron pair, and is called bidentate or polydentate-having two or many " teeth .

在螯合物里，配位体连接在不止一个点上，它们共享一个以上电子对，称为「双齿配位体」或「多齿配位体」，表示说有两个或许多个「牙齿」。

In resting cysts, the microtubules under the pellicle, cortical ciliatures, conjunctions between cilia basal bodies, supporting structure of basal bodies and other microtubule structures are absorbed in different extent; microtubule-like assemble bodies appear at the center of the remained cilia basal bodies; the granules of chromatin and nucleolus in macronucleus become smaller whereas nucleus pores of the micronucleus become bigger; the inner membrane of some nucleus pores are attached with chromatin.

结果表明：纤毛虫形成包囊过程中，皮层细胞质中产生具有自噬泡消化特征的细胞器，将部分纤毛结构等逐步消化；休眠包囊中，表膜下微管、皮层纤毛器和纤毛基体间连接、基体托架及其他微管结构不同程度地被吸收、在残剩纤毛基体的中央形成微管形结构聚合体，大核染色质和核仁颗粒变小，核孔增大，并发生染色质附着于核孔内膜的现象；细胞脱包囊期间，皮层细胞骨架、线粒体等经历了在残剩结构基础上的再分化。

Joining of ceramics and ceramic matrix composites by using preceramic polymer s is a novel technique with lower cost and higher joining strength.

用陶瓷先驱体有机聚合物连接陶瓷及陶瓷基复合材料是一种成本低廉、工艺新颖、可满足特殊高温条件下连接件要求的新型连接技术。

AVI may be protein matrix and it possesses neither a membrane boundary nor an internal structure,its formation is the result of the anthocyanins transported into the vacuole bind with a protein matrix. In vacuole, AVI is irregular and jelly-like in shape. In AVIs, the attachment of anthocyanins to the matrix protein is likely to be via H-bonds to a sterically restricted site. AVI is suggested to act as vacuolar anthocyanin "trap", preferentially for anthocyanidin 3, 5-diglycosides or acylted anthocyanins. The emergence of AVI can enhance color intensity and results in the "blueness" of color in the vacuole.

花色苷液泡包涵体可能具备蛋白质基质，既无膜包裹又无内部结构，其形成是转运进液泡的花色苷与蛋白质基质结合的结果；液泡里的花色苷液泡包涵体形状不规则，象果冻；在花色苷液泡包涵体中，花色苷可能通过氢键连接于蛋白质基质的一个有限空间位点；花色苷液泡包涵体被认为是液泡中花色苷的&陷阱&，优先摄取花色素3，5-二糖苷或酰化的花色苷；花色苷液泡包涵体的存在可增加液泡色彩的强度并导致&蓝化&。

The tryptophan residues play important roles in DNA photoreactivation catalyzed by CPD photolyases. We have investigated the action mechanism concerning Trp in DNA photoreactivation, and obtained the results as follows: 1 We proposed a mechanism of photosensitized splitting of CPDs by Trp and Trp-containing peptides. 2 Quantum yields of splitting of the model compounds that a Trp linked covalently a CPD were obtained under 290 nm light in various solvents, these values changing with solvent, range from 0.01 to 0.5. 3 Utilizing pulse radiolysis technique, splitting processes were observed in aqueous solution of the CPDs with hydrated electron and some oxidative species (such as hydroxyl radical, bromic radical and azide radical), and obtained their rate constants. In the case of interaction between CPD and hydrated electron, splitting of the CPD anion, and pyrimidine anion transfer an electron to FAD or Rf, were observed. The process rate was slower one order more than that in photolyase. Minor, but highly mutagenic UV-light-induced lesions are (6-4) photoproducts, which are repaired by (6-4) photolyases. These enzymes, discovered in 1993, are not well characterized and their mechanism is still under investigation.

我们研究它的作用机理，获得以下结果：1）建立了色氨酸及其肽对嘧啶二聚体光敏化裂解的直接修复作用机理模型；2）获得了色氨酸共价键连接于嘧啶二聚体的化合物在多种溶剂中290nm光辐照裂解的量子效率，其值随溶剂而变化，范围在0.01-0.5；3）运用脉冲辐解观察到嘧啶二聚体与水合电子和一些氧化性的自由基作用裂解过程，得到相应速率常数；对二聚体与水合电子作用发生裂解以及向FAD返还电子的过程进行了体外模拟；4）（6-4）光解酶的作用机理中一个关键假定是氧杂环丁烷中间体在接受电子后能自发裂解，恢复二嘧啶的结构。

The invention also relates to a nozzle body (31) comprising a nozzle outlet which is disposed on the combustion chamber side end thereof, a nozzle needle (33) which is arranged in an axially displaceable manner and/or which can is actuated in a longitudinal recess (32) of the nozzle body (31); a throttle disk (25) which is arranged between the nozzle body (31) and the control valve (20) and which is closed on the rear end (oriented away from the nozzle outlet) of the longitudinal recess (32). Said throttle disk forms an opening stop for the nozzle needle (33) which co-operates with the rear front surface (orientated away from the nozzle outlet) of the nozzle needle (33) and defines the opening stroke of the nozzle needle (33), and a control chamber (45) formed between the rear nozzle needle front surface and the throttle disk (25), said control chamber being hydraulically connected to a pressure connection (29) which is used to supply fuel.

还设置了：一个喷嘴体(31)，在该喷嘴体的燃烧室侧的端部上构成一个喷嘴出口；一个喷嘴针(33)，该喷嘴针在轴向上可运动或可操作地安置在该喷嘴体(31)的一个纵向开口(32)中；一个封闭该纵向开口(32)的后面的端部的、安置在喷嘴体(31)与控制阀(20)之间的节流盘(25)，该节流盘构成用于该喷嘴针(33)的一个打开止挡，在此与该喷嘴针(33)的后面的端面协同作用并由此限定该喷嘴针(33)的打开行程的边界；和一个在该后面的喷嘴针端面与该节流盘(25)之间构成的控制室(45)，该控制室与一个用于燃料输入的压力接口(29)处于液压连接中。

The influence of key factors, including properties of parent metal, relative densities of truss core, an alternative core topology, heat treatment of sandwich panels and the influence of joining technique of truss core and panels on mechanical properties, are analyzed.

分析了基体金属的性能、芯体的相对密度、芯体的拓扑结构、夹芯板的热处理以及芯体和面板的连接方式因素对夹芯板力学性能的影响。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。