进行选择

There are several factors including average altitude, southern slop of hills,gentle slops, under branches, southern Orientation of nests, near to water, nearby places for sandy bathing and covering woods nearby nests that decide the nesting selection of blood pheasant. There are significant differences among the nests of blood pheasants on the nearby vegetation in spite of arbor, shrub and herbage.

作者在血雉产卵期（4.28—5.9）采用跟踪调查的方法，对其巢穴与栖息地生境因子选择进行了调查，结果显示血雉巢穴选择主要生境如下：平均海拔2700米左右、梁下部、南坡、坡度平缓、巢向南、距水源近、巢周围有栖材，有能够用来沙浴的地方，位于树根、树桩下，防风雨、巢材是竹叶、树叶。

This article first has carried on the introduction to the design proposal; And introduced the electric motor choice method, the box body design, the axis design, the gear design, the key choice and so on, then introduced briefly the reduction gear assembles some correlation knowledge and technical order; Finally has listed in the design process glances through and has referred the literature.

本文首先对设计方案进行了介绍；并介绍了电动机的选择方法、箱体的设计、轴的设计、齿轮的设计、键的选择等，然后简要介绍了减速器装配的一些相关知识及技术说明；最后列出了设计过程中翻阅及参考过的文献。

By the ways of documentation,expert interview,statistics and experiment,and applying the relative theories of sports training and sports physiology,training,test and analysis were arranged on the choice reaction time of Shanghai amateur women foil fencers.

采用文献资料法、专家访谈法、数理统计法和实验法等方法，运用运动训练学、运动生理学等相关理论，对上海女子花剑队三线运动员的选择反应时进行训练、测量和分析，从而验证一些反应时的专门训练方法是否能短时间内缩短花剑运动员的选择反应时，提高运动员反应速度，为更好的促进上海女子花剑的发展提供条件。

In the course of care, often choose the local circulation of the largest pharmaceutical enterprises, such as Nanjing local government chose to Nanjing's largest pharmaceutical distributor.

政府在进行托管时，往往会选择当地最大的医药流通企业，比如南京市政府就选择了当地最大的经销商南京医药。

The contents of this design are overall design of FXS900 combination separator and design of Cyclone Collector with Double Outlet for Dust . In the design of the separator, at first, calculate the air amount choose the air fan ,then confirm the diameters of the dust separator room and rotor.

在进行总体设计时，通过风量的计算选择风机，确定旋粉室直径与转子直径，再计算主轴的转速和选粉机的功率，选择电机和减速机。

So this is seen as the main alternative to landfill, not ideal, a sort of least worst option, incinerators like this at Edmonton in North London burning rubbish rather than dumping it in the ground.

因此这被认为是替代垃圾掩埋场的一种主要选择，虽然并不理想，但也是坏处最小的一种选择，那就是焚化炉，就像伦敦北部的埃德蒙顿这里的焚化炉，将垃圾进行焚烧，而不是埋在地下。

In order to investigate the effect of minior actinide data on integral parameter, the accelerator-driven minior actinide benchmark system was selected in this work.

为了确定加速器驱动系统中少錒系核素的核数据的不确定性对此系统中积分参数的影响，选择一铅－铋冷却次临界系统来进行分析，选择不同的微观评价库，CENDL-3.0，JENDL-3.2及ENDF/B-VI。

Then proper adsorbent and corresponding conditions or combining of different adsorbents should be chosen on practical needs.

所以，在实际生产中可根据需要进行树脂和相应的溶液条件选择或不同极性树脂的组合选择。

The law of factors' affecting degree, which influences the parameters between geogrids and soils in the pulling-out procedure, is obtained. With the concept of 'equivalent pull-out displacement' brought forward, the whole process of pull out tests is divided into two process-" main process (when x 1.0)" and "residual process (when x 1.0)", and three stages-static friction resistance stage, slip friction resistance stage, and residual friction resistance stage.2 The value of friction coefficient between reinforcement and soil varies with their definitions of friction, but each factor' s affecting degree influencing friction pa

将模糊控制理论引入了岩土工程过程分析，考虑影响因素影响程度的变化及其规律，提出了一套可供岩土工程过程分析中参数选择的分析方法，并在筋土界面相互作用参数选取的拉拔试验过程控制中获得实施，为应用有限元法对加筋土结构进行过程中南大学博士论文摘要分析提供了参数选择的新方法；将模糊聚类分析方法应用于加筋土陡边坡状态评定，并提出侧向位移可作为加筋土边坡状态评定的量化指标，而不同类型边坡的侧向位移允许控制值可仿效此法结合工程经验确定。

The design method of plastic strcuture is mainly introduced . The selection of the sidewall thickness, the decision of the mould cavity number, the selection of injection machine, and the designing process of the parting plane, the exhaust system, cool material cave and pin gate are stated. The design structure characteristics of box cover and parting plane with pin gate style, and side core-drawing structure.

重点说明了电器盒的塑件结构的设计包括分析和阐述了电器盒塑件的壁厚选择及工艺特点；针对塑件的工艺特点进行模具的设计包括模具型腔数目的确定，注塑机的选择，模具分型面、冷却系统、浇注系统、分型抽芯机构等的设计过程。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新