进行实验

According to simulation results, plastic flow experiment and microchannel formation experiments are carried out.

针对仿真结果进行了塑料流动观察实验和微通道成形实验，实验结果验证了仿真结论。

Two experimental classes are divided into experimental teaching group and controlled teaching group, with their pre-examination, after-examination, and postponed spatial ability examination results of the two groups as quantified analysis, recording the process of teaching as data for teaching activity analysis.

本研究采「实验研究法」之「不等组准实验设计」，以研究者任教之学校为样本，丛集取样二个教学实验班级进行实验组与控制组教学，搜集二组学生在空间能力测验的前测、后测及延后测成绩做为量化分析之依据；记录教学历程做为分析教学活动内涵之资料。

The pulling out experiment was performed by AGS-10KN material testing machine to measure the maximal axial pulling-out strength of hollow nail and the maximal loading when the nail was loose during anti-bending cycle experiments.

拔出实验在AGS-10KN材料实验机上进行，测定空心钉最大轴向拔出力，以及周期抗屈实验中螺钉松动时的最大负荷。

Finally, the experiment equipment was improved and separation characteristics of two-phase vortex tube were studied by conducted experiment.

最后，根据喷嘴形式的分析结果改进实验设备，设计两相涡流管实验流程并进行了相关实验，得到了两相涡流管混合物分离的基本特性。

The angle of rotating mass of a crankshaft-connecting rod and the ratio of rotating mass and to-and-fro mass are important parameters.

讨论了曲柄连杆机构的理论惯性力曲线和实验惯性力曲线(力8字)的关系，提出在摆架上逐点偏移汽缸进行惯性力实验的方法，得到的实验惯性力曲线完全反映了惯性力的主要参数。

Main works of the author:(1) Has developed a design of charge amplifier which using a kind of integrated chip replace a large number of leave components, though all the realized proposal of measurement circuit for the piezoelectric accelerometer;(2) Has made the circuit board;(3) Has proposed a programme-controlled scheme in the sensitivity throw-over of charge convert and gain throw-over of output amplifier;(4) Has done the experiment, give the experimental result;(5) Has done the error analysis based on the experimental result and the principle of the charge amplifier.

作者完成的主要工作包括：(1)通过对压电加速度传感器的测量电路的各种实现方案的深入调研，提出了一种用集成芯片取代大量分离元件的电荷放大器的实现方案；(2)制作了完整的电路板；(3)在电荷转换部分的灵敏电容的切换和输出放大级的增益切换电路的实现上提出了程控的方案；(4)进行了实验验证，给出了实验结果；(5)在实验结果的基础上，结合电荷放大器原理对系统作了误差分析。

Experimental researches on operating characteristics of three-electrode repetitive gas switch were performed on the accelerator CHP01, and experimental results were analyzed.

以&CHP01&加速器为实验平台，对自行研制的重复频率三电极气体开关的工作特性开展了实验研究，并对实验结果进行了分析。

It accord with the change tendency of the wind turbine theory.

并和实验值进行比较，发现计算值和实验值有一定的误差，但是与实验值的变化趋势相同，表明小翼对风力机确实起到的动力放大的作用。

The setups and schemes for experimental study are designed according to the characters of friction contact between slide guide and rail along lateral and vertical directions. Experimental results are processed and analyzed.

针对滑动导靴和导轨之间的横向和纵向摩擦的特点，设计了相应的实验装置，拟定了实验方案，并对实验结果进行了初步的分析和处理。

Self-comparison experiments with the same kind of tissue and differential expression experiments with the different kinds of tissue had been done to verify the reproducibility and the accuracy of this technique.

通过同种组织RNA自身比较实验及不同组织RNA的差异分析实验对猪瘟病毒（classic swine fever virus， CSFV）cDNA芯片实验的重复性进行检验。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。