进刀装置

The design of the device using NC Lathe CA6140 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with. from the I / O interface stepper pulse output signal to control the feed rate and itineraries; In order to maintain the function of cutting thread, to the outer end of spindle or other appropriate location loaded pulse generator; Lathe will be transformed into Tailstock manually controlled electric Tailstock.

本设计利用数控装置对CA6140普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。

The design of the device using NC Lathe CA6240 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with.

本设计利用数控装置对CA6240普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。

The engine bed also is equipped with the interconnection,the tool rest auto-feed and the rapid traverse interconnection,the lathe bed both sides skip distance cushion which the hydraulic ressure clamp system,the abnormal cutting traveling schedule stops immediately and so on each kind of safety device,guarantees the operator and the engine bed movement safety.

机床还设有液压夹紧系统，失常切削行程立即停止的联锁、刀架的自动进给与快速移动的联锁、床身两端的越程缓冲等各种安全保护装置，以保证操作者和机床运行的安全。

High efficient stepping feeding device and 45 degree bevelling cutter ensure ACF tacking accuracy.

高精度步进给料装置及45度斜角自动切刀，有效保证 ACF 贴附精度。

High efficient stepping feeding device 45 degree bevelling cutter ensure ACF tacking accuracy.

高精度步进给料装置及45度斜角自动切刀，有效保证ACF贴附精度。

Methods The reverse feeding turning is used, and a series of effective measures are taken, such as selecting optimum tool parameter and cutting allowance, using a stretching apparatus and an axle sleeve follow-rest.

采用反向进给车削，配合以最佳的刀具几何参数、切削用量、拉紧装置和轴套式跟刀架等一系列有效措施。

In addition to the pad with the installation tool, the workpiece can be based on length of the workpiece in the following of mats equidistant not put pieces of wood (cutting in with the check in with the release, the extension units to ensure normal feeding), pieces of wood directly on the bed pad The thickness of the body in order to be able to firm up slightly better job, made of wood semi-circular pit, run-time increase in lubricating oil.

垫块 除跟刀架装置外，还可根据工件长度，在工件下面垫放不等距的木块(在切削中随放随取，保证拖板正常进给)，木块直接垫放在床身上其厚度以能轻微托牢工件为宜，木块制成半圆弧凹坑，运行时加机油润滑。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新