运动学

The suspension developed specifically for the BMW X5 M and the BMW X6 M with its double-track control arm front axle and Integral IV rear axle offers M-specific elastokinematics thanks to stiffer track control arm mounts and hydraulic tiebar mounts at the front as well as stiffer axle support mounts at the rear.

暂停开发了宝马X5 M和宝马X6 M特别是其双轨控制臂前桥和后桥整体四提供的M -特定弹性运动学由于严厉的跟踪控制臂哥林柱支架和液压支架在前线以及严厉轴支持坐骑在后面。

The fish is propelled by undulation s of a long-based dorsal fin while the body axis is in many cases held straight in swimming.

以依靠长背鳍推进的&尼罗河魔鬼&为研究对象，对柔性长鳍波动推进模式的运动学进行了研究。

This thesis aimed at this hotspot, also one of the important regions during the Ninth-and Tenth-Five-Year-Program periods of Chinese Antarctic research. It made use of Radio Echo-Sounding data, surface horizontal ice flow velocity data, digital elevation model data, surface mass accumulation data and the data concerning melting at the bottom of Amery Ice Shelf , to study the grounding line, mass balance, and ice kinematic characteristics of grounded ice sheet and floating ice shelf respectively.

本论文瞄准国际上的这一研究热点地区，同时也是我国&九五&及&十五&期间的南极研究重点地区，利用无线电回波测厚数据、冰面流速数据、数字高程模型数据、冰面物质积累数据及冰架底部融化数据等，对该地区的接地线、物质平衡、陆地冰盖和漂浮冰架的冰川运动学特征等进行了研究。

Based on the kinematic and geometric relationships between the cam and its roller-follower turret, the eOEects on the output of the cam mechanism owing to clearances in the grooved cam and in the roller bearing, preload between the cam and its turret wheel and the cam taper angle have been investigated.

基于运动学和几何关系与凸轮及滚子的跟随者炮塔， eoeects对输出的凸轮机构由于以清拆行动，在沟槽式凸轮，并在滚子轴承，预紧力之间的凸轮和其炮塔车轮及凸轮锥度进行了调查。

The change tendency of the wheel alignment parameters reflects the suspension's kinematic characteristics.

悬架的运动学特性首先反映在车轮定位参数的变化趋势上。

The study of three cone bit of kinematics simulation models and motion characteristics［J］.

三牙轮钻头运动学仿真模型及其运动特点研究［J］。

In this paper, using the method of computer simulation, on the basis of the cone bit geometry and inematics models and the interaction model of bit and rock, the established models are solved through the MATALB programming.

利用计算机仿真方法，在已建立的牙轮钻头几何学、运动学模型和钻头与岩石互作用模型的基础上，通过MATLAB 编程，求解所建立的各模型。

With the geometry model and kinematics model of roller cone rock bit, the interaction model of rock bit and rock is established which was based on the experiment of interaction between single tooth and rock. It is a good fundament for the computer simulation on working action of rock bit drilling.

在牙轮钻头几何学、运动学基础上，利用单齿压入与刮切岩石实验建立了钻头与岩石互作用力学模型，实现了对钻头在钻井过程中工作行为的仿真计算； 2。

The plastic deformation mechanism of the process is explained. The vector equations of the curved conical surface and the figure of the particle motion for the forming process of the bending tube are presented. The theoretical model of stress and strain fields of the forming process is deduced. The practical forming process of tubes of large diameter demonstrates the validity of the new type of design method of the ox-horned core bar and the computation formula of the length of the raw tube.

本文通过研究弯管成形瞬时应力、应变状态及演化过程，阐明了弯管成形过程受力变形特点及力学原理；提出了一种适合弯管变形分析的新单元及数值方法；建立了弯管成形过程应力、应变场&标准图象&；通过研究弯管成形过程金属流动规律及力学条件，阐明了本工艺塑性变形机理；建立了描述弯管成形过程的曲锥面向量方程及其质点运动学图象；推导了弯管成形过程应力、应变场理论模型；结合大口径弯管生产过程，验证了本文给出的新型牛角芯棒设计方法和管坯长度计算公式的正确性。

The main contents include the kinematic and dynamic characteristics of floating body and concept about large body; the kinematic and dynamic conditions and governing equations for constrained floating body; illumination of simple harmonic by decomposition into diffraction and radiation; introduction of relevant effect forces; the formula of velocity potential in waters with constant depth; the scattering by a vertical cylinder with circular cross section.

简述浮体的运动及动力特征、大尺度物体的概念；受约束浮体的运动学及动力学条件及其控制方程；通过分解为绕射和辐射问题讲解简谐运动及有关的作用力；等水深地形上速度势的表达式；铅垂圆柱产生的散射。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。