过程控制

According to the requirements of resistance and insulation strength between conducting plates, this paper advances a design scheme for the control system of bus bar parameter tester, and introduces the design process for the hardware circuit of control system in detail.

本文根据自动检测母导线导电片电阻和导电片之间绝缘强度的要求，提出了母导线参数检测机控制系统的设计方案，并详细介绍了控制系统硬件电路的设计过程。

The welding process of the butt welding machine used to weld bicycle joints employs a cam transmission mechanism. Its procedure is decided by the contour of the cam.

自行车接头对焊机焊接过程的进行采用凸轮机构控制，焊接过程由凸轮的外廓形状所决定。

In this article,the computer control system of the large scale flashing butt welding was introduced in the aspects of the makeup and its realization.

介绍了大型预热闪光焊机微机控制系统的组成及控制过程的实现。

Its goal is realizing automatization of warehouse storage and retrieval, improving reliability of equipment, and making simulation to storage and retrieval, saving cost of creating by any possibility.

论文研究的内容是物流自动化存取过程中的交互控制，目标是实现仓库存取的自动化，提高设备的可靠性。并对设备存取过程进行仿真，尽可能节约建造成本。

In the process of carbon calcinations in rotary kiln, effective control of feeding flux and negative press is the most important to stabilize the calcine zone s temperature and optimize the calcinations process.

在炭素回转窑煅烧生产过程中，给料量和窑尾负压的有效控制是稳定煅烧带温度、优化煅烧过程的重要环节。

Analyze the characteristics of in general use loading terrace that the 3G core net establishes each usage adequately during the period of designing, from can analyze it to be applicable to with the sexual angle high the heat canned use sex control put to pull out foundation, correspond by letter foundation and break down examination and control foundation, and look for from the theories to high can use support of with sex design.

在设计过程中，充分地分析3G核心网设备使用的通用承载平台的特点，从可用性的角度分析其适用于高可用性控制的热插拔基础、通信基础、故障检测与控制基础，并从理论上寻求对高可用性设计的支持。

Through the active control testing on composite material cantilever beam, the process of vibration absorbed is carried out.

通过对悬臂的复合材料梁实施主动控制试验，实现了减振控制过程。

This paper introduces the operating process and control features of the automatic production line of cashmere carding machine, and designs the automatic control system of cashmere carding machine based on the programmable controller.

介绍了羊绒梳理机自动化生产线的工作过程、控制特点，设计了一种基于可编程控制器的羊绒梳理机自动化控制系统。

The relationship between magnesium chloride concentration with density and salinity were analysed respectively, which showed a theoreticl basis for crystallization automatic control of carnallite cold decomposition process.

研究了不同温度下，低钠光卤石分解过程分解液中氯化镁含量、密度、盐度随时间的变化规律，分析了分解液中氯化镁含量与密度、盐度之间的关系，为低钠光卤石分解制备氯化钾结晶过程自动控制提供了理论基础。

Dynamic simulation using Simulink complex control system of cascade control system in the process.

利用simulink动态仿真复杂控制系统中的串级控制系统的工作过程。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。