过盈配合
- 与 过盈配合 相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Like thread joint, wedge joint, pin coupling, key joint, spline joint, full coordinate joint, elastic link joint, riveted joint, welding and glued joint and so on.
如螺纹联接、楔联接、销联接、键联接、花键联接、过盈配合联接、弹性环联接、铆接、焊接和胶接等。
-
Based on the theory of mechanical reliability design, the reliability of tapered interference joint of HSK toolholder is analyzed, the reliability model is established, and the general formula for reliability computation is presented.
采用机械零件强度可靠性设计的方法，对HSK工具系统锥面过盈配合的可靠性进行了分析，建立了刀柄锥面过盈配合的强度可靠性模型，并且应用应力—强度干涉理论推导出了可靠度的计算公式。
-
The article states how to choose the interference fit by analogizing and computing.
阐述了如何通过类比法与计算法确定过盈配合，指出了过盈配合选择与计算的依据和在选择与计算时应该注意的主要问题。
-
Furthermore, the contact finite element was adopted to gain the accurate distribution of strength in the subassembly with the interference between the axle hole and the shaft.
另外，还采用接触单元对孔轴过盈配合联接组件进行了有限元分析，得到更为精确的强度分布。
-
The three types of fit are: clearance, interference and transition.
可以把配合分为三类：间隙配合，过盈配合，过渡配合。
-
The existing of centrifugal force may cause the variation of the interference fit very greatly.
离心力的存在，使得过盈配合特性发生了很大的变化，尤其当主轴高速旋转时，其影响更加明显，成为影响过盈配合特性的主要因素。
-
Tensional stresses, perhaps caused by an interference fit on the shaft, promote diameter increases.
张力过大，也许就造成轴过盈配合，促进直径增加。
-
Interference Fit Fit with interference (Including minimum interference zero).
过盈配合具有过盈的配合。
-
The above analysis and calculation results resolved the problem that how to reasonably select the shrink rang during the design process and confirmed the assembly temperature under different shrink fit, which avoided the blindness of assembly, provided some better suggestion for the design of the rotor and offered reference datum for the safety and the steady running of the rotor.
上述分析计算结果解决了转子设计时过盈的合理选取的问题，并确定了在不同过盈配合情况下转子安装时所需的加热温度值，避免了安装过程的盲目性，对转子的设计工作提供了一些较好的解决方案，为水力测功器安全、稳定运行提供了参考数据。
-
By the contact elemen analysis the shrink fit in impeller with shaft of steam turbines, and the contact stress of shrunk-on disc have been investigated.
套装在轴上的叶轮工作时，由于离心力的影响，会使叶轮内孔增大，以至叶轮与轴之间有可能产生间隙，因此，叶轮与主轴配合必须采用过盈配合。
- 推荐网络例句
-
As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.
每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。
-
Maybe they'll disappear into a pothole.
也许他们将在壶穴里消失
-
But because of its youthful corporate culture—most people are hustled out of the door in their mid-40s—it had no one to send.
但是因为该公司年轻的企业文化——大多数员工在40来岁的时候都被请出公司——一时间没有好的人选。