输出数据

This paper introduced the electric current sensor principle of work and voltage pick-up each kind of parameter, elaborated hands over - hands over the frequency changer the principle of work, has made the simple description to its output current voltage waveform, in addition, this article logarithm has also given quite detailed showing according to the gathering technology.

本次论文介绍了电流传感器的工作原理及电压传感器的各种参数，阐述了交-交变频器的工作原理，对其输出电流电压波形做了简单的描绘，此外，本文对数据采集技术也作了比较详细的说明。

The design of the device using NC Lathe CA6140 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with. from the I / O interface stepper pulse output signal to control the feed rate and itineraries; In order to maintain the function of cutting thread, to the outer end of spindle or other appropriate location loaded pulse generator; Lathe will be transformed into Tailstock manually controlled electric Tailstock.

本设计利用数控装置对CA6140普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。

The design of the device using NC Lathe CA6240 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with.

本设计利用数控装置对CA6240普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。

The output data use the general DXF document format to connect the software of CAD.

数据输出采用通用的DXF 文件格式实现与CAD软件的接口

Signal source data arises by the general purpose computer, output with serial means high speed through PCI bus line, sink hardware system need not any changes.

信号源数据由通用计算机产生，通过PCI总线以串行方式高速输出，接收端硬件系统无需任何改变。

In fuzzy division of input space of the model, the division references consider not only the space distance of input sample data, but also the rule output error, thus defining"generalized sample distance", which makes model structure better.

在模型输入空间的模糊划分中，不单只考虑输入样本数据的"空间距离"，同时将规则输出误差作为输入空间划分的另一依据，由此定义"广义样本距离"，使模型结构更加合理。

This paper studies the algorithm of data processing in self2calibration of inertial platform. Based on a four position turnover test method , constitutes a CV model for output of goniometer.

软件简介：研究了自适应卡尔曼滤波技术在平台射前自标定数据处理中的应用，标定采用四位置标定方法，对角度传感器输出建立常速度模型。

The pulse power supply consists of three-phase half-wave thyristor rectifier and IGBT chopping circuit.

该电源采用三相半波晶闸管整流电路，IGBT进行直流斩波；根据电流电压反馈信号计算偏差，进行数字PI调节获得恒流、恒压输出特性；控制系统通过20mA电流环异步串行通讯接口与人机界面交换数据。

The theory and application is explained in this paper. Software XMGREDIT5 matching ELCIRC is used to generate unstructured grid, and is considered fit for ocean but rivers. Tidal current is simulated and validated well, and sensitivity of current structure to bathymetry is visible. Affection of wind is qualitatively analyzed here. At the same time the model is improved on as required, like the tidal open boundary which could choose not only long period harmonic constant but also short period harmonic constant and tidal level, and multi-point results and flow field data could be exported effectively with binary results.

本文介绍了ELCIRC的理论及使用；基于其在Linux平台下的软件XMGREDIT5生成全三角形网格并评价其特性，认为XMGREDIT5较适合大范围海域而不适用于河道；应用ELCIRC模型计算了长江口的潮流场并进行验证，结果与实测资料吻合良好，且能较好地模拟出地形变化对水流结构的影响；文中对于风场的影响作了定性分析，同时根据实际需要对模型作了改进，如将仅支持长期资料调和常数的开边界条件改为可选择的短期调和常数边界和潮位边界，使二进制格式结果文件数据输出可以处理多点数据及流场等等。

The hardware included helicon wave antenna and focusing system.

其中硬件系统主要包括：螺旋波天线和辉光聚焦系统的设计；PCL-818HG数据采集卡输出的+5V稳定信号，经过分压电阻和三极管后，作为数控器的外部启动/停止信号，控制步进电机带动光谱仪转动；另外，为了减小光电倍增管的噪声，单独为其提供了稳定的高压直流电源。

We have no common name for a mime of Sophron or Xenarchus and a Socratic Conversation; and we should still be without one even if the imitation in the two instances were in trimeters or elegiacs or some other kind of verse--though it is the way with people to tack on 'poet' to the name of a metre, and talk of elegiac-poets and epic-poets, thinking that they call them poets not by reason of the imitative nature of their work, but indiscriminately by reason of the metre they write in.

索夫农 、森那库斯和苏格拉底式的对话采用的模仿没有一个公共的名称；三音步诗、挽歌体或其他类型的诗的模仿也没有——人们把&诗人&这一名词和格律名称结合到一起，称之为挽歌体诗人或者史诗诗人，他们被称为诗人，似乎只是因为遵守格律写作，而非他们作品的模仿本质。

The relationship between communicative competence and grammar teaching should be that of the ends and the means.

交际能力和语法的关系应该是目标与途径的关系。