输出信号

The sine output signal of the FOG is sampled and processed to calculate the direction of surveyed point on the surface of earth.

通过对光纤陀螺输出的正弦信号的采样和处理，即可得到地球表面某参考点的方位。

In the paper, based on the analysis of output noise of FOG, wavelet threshold de-noising theory is applied in FOG's signal processing, and the method is compared with Strong Trace Kalman Filtering optimal estimation method based on ARIMA model.

在分析了光纤陀螺输出噪声的基础上，将小波阈值去噪理论应用到光纤陀螺信号处理中，并与基于ARIMA模型的强跟踪Kalman滤波去噪方法进行了比较。

Because of the influence of inertia force,the output of robot wrist force sensor can not correctly represent the amount of force at the interface between the robot gripper and the enviroment.

由于惯性力的影响，机器人腕力传感器输出的六维信号不能准确反映机械手夹持器与外界环境接触力的大小。

The design of the device using NC Lathe CA6140 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with. from the I / O interface stepper pulse output signal to control the feed rate and itineraries; In order to maintain the function of cutting thread, to the outer end of spindle or other appropriate location loaded pulse generator; Lathe will be transformed into Tailstock manually controlled electric Tailstock.

本设计利用数控装置对CA6140普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。

The design of the device using NC Lathe CA6240 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with.

本设计利用数控装置对CA6240普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。

Signal source data arises by the general purpose computer, output with serial means high speed through PCI bus line, sink hardware system need not any changes.

信号源数据由通用计算机产生，通过PCI总线以串行方式高速输出，接收端硬件系统无需任何改变。

One can choose the output sine wave square wave triangle wave signal generator, but with graphical input method.

详细说明：一个可以选择输出正弦波三角波方波的信号发生器，不过是用图形输入法。

The pulse power supply consists of three-phase half-wave thyristor rectifier and IGBT chopping circuit.

该电源采用三相半波晶闸管整流电路，IGBT进行直流斩波；根据电流电压反馈信号计算偏差，进行数字PI调节获得恒流、恒压输出特性；控制系统通过20mA电流环异步串行通讯接口与人机界面交换数据。

In this paper, based on Delta Operator, signal vectors of Hilbert space are constructed, an input-output model is derived, and both the forward and backward prediction error vectors are described.

摘要本文基于δ算子构造了Hilbert空间中的信号向量，推导了系统的输入输出关系，得出了前向和后向预测误差向量的表达式。

Dynamical behaviors such as periodic, quasi-periodic and chaotic waveforms are observed on oscilloscope. It is expected that the proposed chaotic sources and their circuit implementations are beneficial to the application of neural networks. 4 A template of Cellular Neural Network is derived aimed at solving second-order hyperbolic wave equations based on space discrete method, a novel alternating recursive algorithm implementation is given.

提出了采用复数神经网络进行FIR滤波器设计的方法，利用复数信号能够同时携带幅度和相位信息的特点，构造了相应的具有复数的状态、偏置输入、输出、网络联接权的复数神经网络，证明了算法的收敛性，给出了网络的电路实现图，这方面工作对于拓展神经网络算法的应用范围和寻求FIR滤波器的设计新方法是有益的。

We have no common name for a mime of Sophron or Xenarchus and a Socratic Conversation; and we should still be without one even if the imitation in the two instances were in trimeters or elegiacs or some other kind of verse--though it is the way with people to tack on 'poet' to the name of a metre, and talk of elegiac-poets and epic-poets, thinking that they call them poets not by reason of the imitative nature of their work, but indiscriminately by reason of the metre they write in.

索夫农 、森那库斯和苏格拉底式的对话采用的模仿没有一个公共的名称；三音步诗、挽歌体或其他类型的诗的模仿也没有——人们把&诗人&这一名词和格律名称结合到一起，称之为挽歌体诗人或者史诗诗人，他们被称为诗人，似乎只是因为遵守格律写作，而非他们作品的模仿本质。

The relationship between communicative competence and grammar teaching should be that of the ends and the means.

交际能力和语法的关系应该是目标与途径的关系。