输入电阻

This resistor assures that in the case of input con- trol or input feedback wire interruption the input differential voltage will be within the NEUTRAL ZONE and the motor position remains frozen.

这个电阻保证，在输入CON组，特伦或输入的反馈线中断的输入差分电压的情况将在中立区和电机的立场仍然冻结。

The restriction of equivalent transformation analysis method is discussed and finally a proper method and the result of the analysis are offered.

在单端输入的差动放大电路工作原理教学中，对共模反馈电阻R e的作用，往往采用等效变换法进行分析，如果不注意正确使用分析条件会得出错误的结论，本文从理论和实践上指出了利用这种分析方法分析单端输入差动放大电路的局限性，最后给出了正确的分析方法及结论。

The feedback resistance, R1, is dependent on cell sensitivity and should be chosen for either maximum dynamic range or for a desired scale factor. R2 is elective: in the case of photovoltaic cells or of photodiodes, it is not required in the case of photoconductive cells, it should be chosen to minimize bias current error over the operating range.

反馈电阻R1的取值由电池的灵敏度和要求的最大动态范围，或者需要的电流——电压转换比例决定。R2分情况选取：在光电池和光电二极管时不需要这个电阻，在光电导的时候，电阻的阻值应该能使在工作范围内，由OP输入偏置电流所带来的误差最小。

But if the Hall IC use a 12V supply, additional pull-down resistor and zenor diode would be needed to clamp the voltage in case of the Hall input voltage would exceed 5V.

但是，如果 Hall IC 使用 12V 的电源，为了使 Hall 输入的电压不超过 5V，必须再附加下拉电阻，齐纳二极管等来钳制输入电压。

S1 is then changed to position 1. The voltage stored on C1 is inserted between the output and inverting input of the amplifier and the output of the amplifier changes by VIN to maintain the amplifier input at the input offset voltage. The output then changes from (VOS + IbiasR2) to (VIN + IbiasR2) as S1 is changed from position 2 to position 1. Amplifier bias current is supplied through R2 from the output of the amplifier or from C2 when S1 is in position 2 and position 1 respectively. R3 serves to reduce the offset at the amplifier output if the amplifier must have maximum linear range or if it is desired to DC couple the amplifier.

接着 S1 拨到位置 1，使 C1 的电压加在放大器的输出端和反相输入端之间，(由于电容端电压不能突变，所以)输出端的电压将产生大小等于 VIN 的变化，使放大器输入端维持输入失调电压，即当开关 S1 从位置 2 拨到位置 1 时，输出端电压将从(VOS + IbiasR2)变为(VIN + IbiasR2)。S1 处于位置 2 时，放大器的偏置电流是由输出端经电阻 R2 提供的，当 S1 转向位置 1 时则由 C2 提供。R3 的作用是降低输出失调电压，如果要求放大器具有最大的线性范围，或者采用直流耦合，就应该使用该电容。

A resistor is connected between the output end of the live wire and the output end of the earth wire, another resistor is connected between the output end of the null line and the input end of the earth wire, a neon lamp in a photoelectric coupling switch is connected at the two ends of the earth wire switch in parallel after being connected with the resistors in series, one end of a light sensitive resistor in the photoelectric coupling switch GR2 is connected with the anode DC+ of an integrated circuit IC power in the creepage protector, the other end of the light sensitive resistor is connected with the anode of a diode D3, the cathode of the diode D3 is connected with the triggering pole of the silicon-controlled rectifier SCR in the creepage protector, the neon lamp and the light sensitive resistor are positioned into a dark box, and a small hole which avoids the light sensitive resistor is formed on the dark box.

一种防止地线触点未导通的全能安全插头，包括各带开关的地、零、相三线接线和由零序互感器、脱扣器、放大器、整流器、试验回路和可控硅组成的漏电保护器，所述的火线输出端、地线输出端间连接电阻，所述的零线输出端、地线输入端间串接电阻，光电耦合开关内的氖灯与电阻串联后并联在地线开关两端，光电耦合开关GR2内光敏电阻的一端与漏电保护器内的集成电路IC电源正极DC＋连接、光敏电阻的另一端与二极管D3的正极连接，二极管D3的负极与漏电保护器内的可控硅SCR触发极连接，氖灯和光敏电阻置于暗箱中，暗箱上开一避开光敏电阻的小孔。

After being connected with a resistor in series, the primary input end of a transformer is connected with the output end of the live wire and the output end of the null line in parallel, the secondary output end is connected with the two ends of the earth wire switch in parallel after being connected with another resistor in series, one end of a neon lamp in a photoelectric coupler is connected with the input end of the earth wire E and a secondary end of the transformer, the other end of the neon lamp is connected with the centers of the two resistors, one end of a light sensitive resistor in a photoelectric coupling switch is connected with the anode of an integrated circuit power in the creepage protector, the other end of the light sensitive resistor is connected with the anode of a diode, the cathode of the diode is connected with the triggering pole of the silicon-controlled rectifier in the creepage protector, the neon lamp and the light sensitive resistor are positioned into a dark box, and a small hole which avoids the light sensitive resistor is formed on the dark box.

防止地线触点未导通的全能安全插头，包括各带开关的地、零、相三线接线和由零序互感器、脱扣器、放大器、整流器、试验回路和可控硅组成的漏电保护器，变压器初级输入端串联电阻后并接在火线输出端和零线输出端，次级输出端与电阻串联后并联在地线开关两端，光耦内氖灯的一端与地线E输入端和变压器次级的一端连接，氖灯另一端与二电阻的中心连接，光电耦合开关内光敏电阻的一端与漏电保护器内的集成电路电源正极连接、光敏电阻的另一端与二极管的正极连接，二极管的负极与漏电保护器内的可控硅触发极连接，氖灯和光敏电阻置于暗箱中，暗箱上开一避开光敏电阻的小孔。

Therefore, the exact relation between the unbalanced input voltage and the noncharacteristic harmonics of the output voltage in the 12-pulse rectifier system is obtained. In addition, the relation between the input current and the imbalance of the input voltage is obtained, which could help to choose the filter elements and exactly analyze the characteristics of the no controlled rectifier circuit.

利用精确的开关函数，推导了多脉波整流系统输入不平衡电压与输出电压非特征谐波的精确关系，进而得到电阻、电感负载时系统输入电流与输入电压不平衡度的关系，为精确地选择滤波元件做了有意义的探索。

Modern digital voltmeters have input resistances that range from 10 megohms to nearly 10,000 megohms.

现代化的数字伏特计有从10兆欧到10，000兆欧的输入电阻。

Accurate ratio matching and temperature tracking of the input resis- tors provides improved stability of the half-scale offset.

准确率和温度匹配的输入电阻，职责范围跟踪提供了改进的一半规模的稳定抵消。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。