辊轧机

This proves that the calculating results of streamline strip element method are reliable, and satisfied with demands from engineer work.

关于300mm四辊冷带轧机轧制铝带压力摩擦力张力和1850mm六辊CVC冷带轧机轧制铝合金带前张力横向分布的计算结果与实验结果吻合较好，证明了该流线条元法计算结果可靠，可满足工程实际要求。

Having analyzed the axial damping characteristic of the rolling strip mill, the scale of axial damping factor is established.

还可对一些特殊轧机，如PC轧机、CVC轧机、HC轧机等进行辊系特性的分析，是对轧机研究理论和计算模型的丰富和发展。

Based on the dyanamic analysis of position loop system for the use of four roll hydraulic mill, analyses of thickness precontrol and monitored control function and constitutent are given; and the design procedure of a digital controller and specific plan of microcomputer implementetion are also given.

在四辊液压轧机位置闭环系统动态分析的基础上，分析厚度预控和监控的功能、组成数字控制器的设计方法，以及微机实现的具体方案。将其应用到Φ(2 1 0～ 5 0 0 )mm× 80 0mm四辊液压轧机上，使轧机具有较强的消差能力，并使出口带材能锁定在要求的目标尺寸上

Based on the failure type of the guide roller for bar or wire mill, the contrasting experiment on the high temperature wear resistance of GJH 2 cermets and Gx casting alloys at different heat treatment condition and temperature was carried out, and the GJH 2 cermet was used as the guide roller of mill.

在分析棒、线材轧机使用的 Gx铸造合金导卫辊失效形式的基础上，对不同热处理状态的GJH- 2合金和 Gx铸造合金，在不同温度下的高温磨损特性进行了对比试验，并将 GJH- 2合金制成导卫辊在轧机上进行了装机试验。

A new process for seamless tube production called Seamless Tube Process comes into our horizon. The key equipment is a four—roll planetary rolling mill, which is also called Kocks Reduction Mill. The structure and operation principle of four-roll planetary rolling mill is similar to the three-roll planetary rolling mill.

最近出现了一种新的轧管工艺——STP轧管工艺，其核心设备为四辊行星轧机，又称KRM轧管机，其结构和工作原理与三辊行星轧机类似。

Aimed at all kinds of damage phenomena in the sleeve usage of oil-film bearing in the backup roll of Baoshan 1580 hot strip mill,during the process of elastic conjunction between sleeve and rollneck,deformation and load properties are quantitatively analyzed by boundary element method for 3D elastic and plastic contact problems.

针对宝钢1580热连轧机精轧机组支承辊油膜轴承锥套使用中存在的各类损伤问题，利用三维弹塑性接触问题边界元法定量分析了轧机油膜轴承锥套与轧辊辊颈过盈装配过程中的变形和载荷特性，得出了装拆过程中不同的胀型压力和轴向推力条件下锥套接触压力延母线方向的变化规律，同时锥套端部和密封槽附近接触压力峰值的存在是加速锥套损伤及降低其使用寿命的重要原因。

The structural principle, rolling mechanism and movement rules of the three-roll planetary mill have been introduced.

阐述了三辊行星轧机的结构原理、轧制机理及其运动情况，在对三辊行星轧机分析研究的基础上，设计制造了一种新型三辊旋轧试验机。

The characteristic of this series leveler iS that it has adopted two national patent technologies:group driving plate levelling machine ZL200420001176.0 and axial decelerating motor leveler ZL200520007514.6.Each top roll is driven by a set of decelerating motor.and every two lower rolls are driven by a set of dynamic system,so that the line speed of each roll iS consistent with sheet metal speed of the contacting part,and it has solved the problems existing in traditional transmission system,such as friction between sheet metal and roll surface.and mechanical interference problem in the system And the working roll adopts spherical roller bearings which have little friction resistance.so this series leveler has such advantages as high levelIing quality,Iittle noise,low energy consumption and environmental protection.compared with traditional levelers.

该系列矫平机的特色之处在于：采用分组驱动板材矫正机(ZL200420001176.0)和一种轴装式减速电机矫平机(ZL200520007514.6)两种国家专利技术，每根上辊由一套减速电机驱动，每两根下辊由一套动力系统驱动，从而使各辊的线速度与所接触部位的板料速度相一致，消除了传统传动系统存在的板料与辊面之间的摩擦和传动系统内部的机械干涉问题，同时由于工作辊的轴承均采用轧机用调心辊子轴承，摩擦阻力小，因此，该系列矫平机与传统矫平机相比，矫平质量高、噪音小、能耗低、节能环保。

CNC multi-functional grinder used for the grinding of R1,R2, work roll of rolling machine and F1~F7 work roll, pinch roll and forming roller, 1 CNC multi-functional grinder used for the grinding of F1~F7 work roll.

1台CNC型万能轧辊磨床，该磨床用于 R1、 R2、轧机工作辊/支承辊及 F1~F7支承辊、夹送辊及助卷辊的修磨、4台 CNC 型工作辊磨床，用于 F1~F7工作辊的修磨。

With the character of CVC roll curve, the strip thickness distribution, rolling pressure distribution and pressure between rolls along transverse direction are calculated, by using the model of the real roll crown distribution and the character of the antisymmetry of mills. The results are in good agreement with production data.

根据CVC轧辊辊形的特点，采用实际轧辊凸度分布模型，并利用轧机的反对称性质，计算轧机垂直中心线一侧的板断面厚度分布、轧制力分布、辊间压力分布等，提高了板形计算和辊间压力计算的精度，模拟计算结果与现场数据相符。

James, son of Zebedee, and John the brother of James, whom he named Boanerges, that is, sons of thunder

载伯德的儿子雅各伯和雅各伯的弟弟若望，并为他们起名叫"波纳尔革"，就是"雷霆之子"

The southern Hungarian university city of Szeged will host part of the project, amounting to 40 percent of the total investment, which will mostly be paid for through Hungary's EU structural funds.

位于塞格德南部的匈牙利大学将负责部分项目，总计占总投入资金的40%。大部分资金将由匈牙利的欧盟结构基金会支付。