较大的

The results indicate that, in either single or double blowing, larger erosion rate is mainly found in the slag line and near purging plug area of ladle lining; erosion is accelerated when gas flow rate increases; the erosion rate of ladle lining with double blowing is larger than that of single blowing; erosion rate distribution is obviously different as gas flow rate increases; in heavy blowing, serious erosion centers around slag line area and expands gradually outwards; as purging plug gets close to lining wall, malconformation of erosion rate in ladle lining becomes more prominent and the erosion rate of lining near purging plug increases.

结果表明，无论单吹还是复吹，较大的蚀损速率主要分布在钢包渣线及近透气砖区域，吹气量的增大会加速钢包内衬的蚀损。采用复吹时，钢包内衬的蚀损较单吹时更快。随着吹气参数的改变，钢包内衬蚀损速率的分布状况差异明显。大吹气量下，较大的蚀损集中在渣线区域且呈环向扩展；透气砖安装距包壁越近，钢包内衬蚀损不均衡性也越突出，近透气砖内衬蚀损加重。

The gel dynamics experiments showed that the gel formation law was similar with the other polymer systems, which wasrelated with dense surface under the soft coagulating condition and the thickening gel; the square of gel thickness was linear with coagulation time. The qualitative analysis of the surface puckers of fibers spun from wet spinning and dry-jet wet spinning was made. The positions where the die swell appeared were not the same and the die swell appeared at the air gap where the fiber would markedly been elongated and vary little in the coagulant, thus the surface of fiber spun from dry-jet wet spinning was more smooth. The radial component concentration gradient was responsible for the radial structure of PAN fiber spun from dry-jet wet spinning. The thicker surface with microvoid structure of

对湿纺和干湿纺进行比较表层沟槽的产生进行定性分析，原因在于孔口胀大区域出现在不同位置，在干湿纺中，溶液的孔口胀大出现在空气层，并在该区完成大部分形变，进入凝固浴后形变很小，纤维表面较为光滑；干湿纺PAN纤维径向结构存在差异，这与丝条内组分由于双扩散进行导致径向上存在浓度差异直接相关；凝固强度较大的体系，可以获得厚度较大且孔结构尺寸较小的皮层；含较少缠结的PAN原液在纤维成形后截面很圆整，但原液缠结浓度增大时成形后圆整度下降；PAN纤维成形是一个远离平衡的过程，凝固作用缓和的体系可以使成形过程靠近平衡，可获得更大尺寸的孔洞结构；原液中少量的非溶剂添加剂显著改变纤维径向结构，可获得孔洞尺寸更小和更为均一的径向结构，这与径向浓度差异的减小、分相时间的集中相关；PAN原液的成形纤维表面依赖于凝固强度；由AFM对相近凝固条件下成形的PAN膜进下

Once the sparger installed in the CMT, the fluid temperature above the sparger and the initial pressure of pressurizer are the key factor, which affect the condensation characteristic and temperature equilibrium time.

通过对不同初始条件下的CMT排水量进行了分析，发现CMT排水速度主要受CMT内的压力变化的影响：CMT无遮流板排水实验中所有排水量随时间的变化曲线都是单调递增的，且都有一个较为明显的拐点，在拐点后，斜率明显增大，说明排水速度增加显著；CMT加遮流板排水实验中排水量曲线的拐点不明显且出现时间较无遮流板排水实验要早，说明排水速度增加得较早；CMT加遮流板排水实验如果PRZ初始压力较大，通过改变CMT的初始温度，将会引起排水总量较大的变化；排水速度平衡时间受CMT压力平衡响应时间的影响，且较CMT压力平衡响应时间快。

Classification and principle of rigid waterproofer;2. The circinal cavities were found in calcium alginate beads and the cylinder holes were observed in zinc alginate beads from the SEM,which indicated that the volume of fraction of zinc alginate polymer was relatively bigger and the zinc alginate polymer chain was more rigid than that of calcium alginate .

凝胶的SEM照片可见，海藻酸钙的冷冻干燥颗粒内为较大的圆孔，海藻酸锌凝胶内为较小的长孔，表明海藻酸锌高分子链在凝胶颗粒中的体积分率相对较大同时刚性较强；卵清蛋白从海藻酸凝胶颗粒中释放的试验结果表明，由于上述海藻酸锌凝胶的特性，导致海藻酸锌对卵清蛋白扩散阻滞作用相对较强；根据试验数据计算得卵清蛋白在海藻酸钙、海藻酸锌凝胶颗粒中的扩散系数分别为1。

Maturation feeding weevils displayed higher anemotaxis responses to -β- pinene, myrene and limonene than those of sexually matured weevils; whereas - carene, which was detected only in volatiles of trunk phloem, elicted more olfactory respones of sexually matured weevils than of maturation feeding weevils.

在华山松枝梢挥发物中含量较高的-β-蒎烯、月桂烯和柠檬烯引起补充营养期华山松木蠹象较大的趋向反应；在华山松树干韧皮部挥发物中含量较高的3--蒈烯则引起交尾产卵期的华山松木蠹象较大的趋向反应。

The concentration of chlorophyll a was higher in the aquacultural area,and had no distinct seasonal changes,whereas...

调查海区表层海水叶绿素a含量在近岸养殖区较高，季节变化不明显，但其粒级结构有较大的季节差异；初级生产力的平面分布与叶绿素a含量在春、秋季均较一致，其粒级结构与叶绿素a的粒级结构在春季基本一致，但在秋季有较大差异。

Exterior refinements include:+ A larger, polished stainless steel wire mesh front grille that enables the required additional airflow for engine heat dissipation + A new, lower front fascia that incorporates a larger lower grille for increased cooling capability; brake ducts for front caliper and rotor cooling and splitter to counteract lift created by larger grille openings + A new lower rear fascia that facilitates smooth airflow under the vehicle for improved cooling + Lower rockers that visually bridge the lowered front and rear fascias + A specific, fluidly sculpted hood designed to provide space for the engine's supercharger + Ten-spoke, flangeless, painted aluminum alloy wheels that assist in brake cooling + A higher, more rearward-positioned rear spoiler that enables balanced aerodynamic downforce with the front splitter + V-series badging on the vehicle's rear decklid and front doors, and "Supercharged" block lettering on the doors

外观的改进包括：+有较大，抛光不锈钢丝网的前格栅，使发动机所需的额外的散热气流+一个新的，较低的前仪表，它把一个较大的下格栅关于提高冷却能力；刹车管为卡钳和转子冷却和分配器足以抵消格栅的开口更大的提升+创建一个新的较低的后部汽车仪表板，便于在改善冷却车辆气流平稳+下摇滚乐的视觉弥补降低的前后面板+一个具体的，流畅，造型盖设计为发动机的增压器+十空间发言，凸缘，画铝合金轮毂的协助刹车冷却+阿更高，更向后定位的后扰流板，使平衡与前分路空气下压力+ V系列徽章的车的后部行李箱的大门，和&增压&块门上刻字

Some conclusions are drawn from the calculating results: when buried pipes cross fault, pipe's embedded depth should be shallow, and big pipe diameter and thick wall should be selected. Avoid the site where fault moves severe, and select suitable pipe-fault angle. Bigger pipe-soil friction coefficient is helpful for buried pipe crossing fault. Under dynamic loading, buried pipe would first damaged in compressive region of bilateral fault, so special treatment should be done to pipe in bilateral fault region.

依据计算结果分析了各因素对地下管道破坏的影响，并得出几点结论：管土摩擦系数较大情况下，管道破坏较轻；地下管道在穿越断层时，管道宜浅埋，并选取大管径、壁厚的管道；应尽量避开断层错动较大的位置，并选取合适的管道穿越断层角度；在受动荷载作用时，管道在断层两侧受压区先破坏，故在断层两侧要进行特殊处理进行防护。

The results show that the PCR scheme is not only suitable for urban area with high traffic load and low mobility, but also can significantly reduce the probability of dropping handovers for the freeway system, of which the traffic load is considerably high.

数值结果表明：该方案不仅适用于车辆运行速度较低、通信负载较大的城市交通系统，而且对通信负载量较大的高速公路通信系统，其越区切换的掉话率也能得到较明显地改善。

Chirp scaling algorithm is considered more efficient and widely applicable when the bistatic SAR system is in side-look or small squint angle mode,but in large squint angle case,the errors caused by Taylor expansion are so large that the algorithm could lose its precision.In such a case,an equivalent mono-static SAR range mode which has fewer errors than Taylor expansion with large squint angle is proposed to substitute the range history of bistatic SAR.Then bistatic SAR images with large squint angles are gotten by common Nonlinear CS algorithm.The effectivity of the method is verified by Matlab simulation.

在正侧视或小斜视情况下，CS算法具有较好的聚焦性能和广泛的适用性，但在斜视角较大的情况下，该算法将散焦而不能成像，因而提出了用等效的单基地距离模型来代替双基地距离历史的方法，解决了大斜视角情况下距离模型二阶近似误差较大的问题，并结合单基地非线性CS算法，实现了在大斜视角情况下的基于GPS反射信号的双基地SAR高精度成像，最后通过Matlab仿真进行了验证。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。