轴面

All the patterns in bud and different parts of scale change at different stages,and the peroxidase activity in bud and adaxial epiderm is higher than that in the inner tissue of scale.

发现芽和鳞片不同部位的同工酶谱带在解除休眠的不同时期均有变化，且芽和鳞片近轴面表皮的过氧化物酶活性明显高于鳞片内部组织。

In the present study, only T2-weighted images were aailable for assessment; T1-weighted images had been taken in the axial plane for measurements of erector spinae muscle size,24 and it was not feasible to also obtain T1-weighted sagittal images.

在我们的研究中，仅有T2加权像被用来进行评定，我们做的轴面T1加权像被用来测量骶棘肌的大小了[24]，而同样也获得矢状位的T1加权像是不太可行的。

The differences of the width, volume and maximum height of Z profile signal of macula were analyzed.

对比分析其扫描图像的Z轴面信号宽度、容积、最大深度的异同。

The pressure distributions and meridional velocity distributions of two impellers designed with different design variables were ana...

研究表明：轴面流道形状和叶轮包角影响叶轮内部压力场和速度场的均匀性，导致两个叶轮的水力效率值存在约2%的差别。

The Optimization of pinacoid flow passage, which cant be realized by single parameterized technology, is figured out with behavioral modeling. By establishing the optimal characteristics, the complex and repetitive process of impeller design is turned into an automatic one.

利用行为建模技术解决了单一参数化技术无法解决的轴面流道的优化问题，将叶轮设计的大量重复、费时费力的一个复杂设计过程，通过优化特征的建立，变成了一个自动化的过程。

This paper presents the dynamic controlling method of stream lines on axial plane projection of the hydraulic model and square grid of the blade drawing of the pump impeller. The ideas and methods of the application of Bezier curve in impeller CAD are analyzed in detail.

提出采用Bezier曲线解决水泵叶轮水力模型轴面投影流线及叶片绘型的方格网流线的动态调控方法，详尽地分析了在叶轮CAD中应用Bezier曲线的具体思路与方法。

Methods Eighteen patients with biliary calculi underwent volume scanning using spiral CT (Hispeed Advantage CT/i GE ). All data were transferred to computer workstation, and CT biliary virtual endoscopy images with pseudocolor encoding were generated from the volumatric data using the Navigator Smooth soft-ware.

选择18例胆道结石患者行横轴面CT扫描，将容积数据重建后输入计算机工作站，用三维导航软件功能重建成仿真内窥镜图像，调整阈值并用伪彩色技术立体观察结石。

To overcome the inconvenience of traditional centrifugal pump impeller design, the quartic Bezier curve is used to design the meridional plane and blade profile.

针对传统离心泵叶轮设计步骤繁琐的不足，提出了采用4次Bezier曲线来设计叶轮的轴面流线及叶片型线的方法。

The floral primordium is initially circular, along with the edge of which slight concaves occur. The outmost whorl of tepal primordia arises as a result of apical meristem division and the floral primordium then is in the shape of triangle. Two further whorls of tepal primordia arise in spiral acropetal sequence and are alternately arranged. When the innermost whorl of tepal primordia is at the late developmental stage, the foremost stamen primordia arise almost simultaneously in spiral acropetal succession and all of the stamen primordia are ultimately arranged in a triangle-cone form. Late in stamen primordium development, carpel primordia arise as same as the young stamen primordia and grow laterally. Grooves are present on the adaxial side of each carpel and develop into ventral sutures gradually closing up.

观光木的花原基最初为近圆形，随着顶端分生组织的活动，花原基边缘处出现浅凹，形成第一轮花被片原基，此时，花原基呈三角形排列，后两轮花被片原基依次发生，与前一轮互生；在内轮花被片发生的后期，最初几枚雄蕊原基几乎同时出现，呈螺旋状向顶发生，最后排列成三角圆锥状；雄蕊原基发育后期，心皮原基开始发育，形状与发育初期的雄蕊原基相似，随后心皮原基进行侧向生长，在近轴面出现浅凹，进而发育为凹槽，形成腹缝线，最后腹缝线完全愈合。

In addition, KANADI and YABBY act in the abaxial domain of leaves to specify the abaxial identity.

KANADI和YABBY基因在远轴面极性建成中起作用。

I will endeavour to find you some assistance.

我尽力帮你找人帮忙。

At first I only know bruck is the idol of American younglings, afterwards I returned back to Taiwan ,even in Beijing last year ,I saw her poster everywhere, I was so surprised at her charm.

起初我只晓得布鲁克雷德丝是美国少男少女崇拜的偶像，后来回台湾，甚至去年在北京，居然也四处看见她的海报，才惊讶她的魅力之大。