轴面
- 与 轴面 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
In this species, the first division of zygote produces two equal hemispheric cells by the first partition wall at the right angles to the axis of the archegonium.
合子的第一次分裂面垂直于颈卵器的长轴,产生两个相等的子细胞,靠近颈卵器颈部的营养器官原始细胞和远离颈部的基足原始细胞。
-
To create an axis through a cylinder, its value should be the revolved surface of the cylinder, represented as a ProSelection object.
为创建个穿过柱面的轴,它的值应当是旋转的柱面,用个 ProSelection 对象表示。
-
Based on the shortest distance between the cylinder cutter axis and surrounding surface, the maximum gouging was obtained by comparing with the radius of cutter.
提出的柱刀干涉检测是基于最短距离的求取算法,获得刀轴与加工面间的最短距离,进而与刀具半径比较得到最大干涉量。
-
Figure 3.10, click here to view all press photos from the installation requirements, the axis of the plate cylinder and oscillating axle-level of the roll is still parallel to one another.
图3.10不面击此处查察全部故事图片从安设的请求来讲,印版滚筒的轴线和串不朱辊的轴级仍为交错线。
-
Areas must lie to one side of, and in the plane of, the axis of rotation.
这些面必须位于轴的一侧,且必须同处在一个平面上。
-
Shear strength distribution of the axial and azimuthal flow is studied for the first time in this paper.
轴向流剪切力绝对值在环隙中部最大,向两侧逐渐递减,在两筒壁面最小。
-
According to the quantitative analysis, the critical time to stop or run back the wheel and shaft when the driving rotor generating an impulse during strike of the return high-pressure gas is calculated...
介绍了我厂关键设备氧化铝沸腾焙烧炉罗茨鼓风机的功能,及自1997年11月投产以来先后发生四次事故的情况,重点分析了由于高压气体回流冲击而使同步齿轮与轴配合面产生相对滑移的可能,通过定量分析计算高压气体回流冲击时对主动转子产生冲量使其停止或反转的临界时间,同时提出了预防措施。
-
The results indicate that the discontinuous surface such as weak interlayer, bedding plane and joints are the major factors which control the deformation of the rock mass, the existence of weak interlayer influenced the distribution of shear displacement, stress and plastic zones, which is also a major factor result the axial forces increased rapidly during construction.
结果表明,结构面(如软弱夹层、层面和节理裂隙等)是控制图岩变形的主要因素,软弱夹层的存在控制了围岩剪位移、应力和塑性区的分布,是导致锚杆轴力增大的主要因素,实时监测资料和理论计算成果吻合良好。
-
This paper deals with the initiation and non-coplaner propagation of cracks under biaxial compression.
本文研究了双轴压缩载荷下裂纹的起裂和非共面传播问题。
-
Book equipment application in automobile, motorcycle, machinery foundation profession such as chain, fastener, bearing, box spanner, tool, special different type nut and flange surface nut, sides nut, welding nut, cover type nut , locknut, defence pine nut, pull hat nut, chain Luo pull, expansion gecko, independently axle gear, bicycle different type etc.
本设备应用于汽车、摩托车、机械基础行业(如链条、紧固件、轴承、套筒扳手、工具、特殊异型螺母、法兰面螺母、四方螺母、焊接螺母、盖型螺母、锁紧螺母、防松螺母、拉帽螺母、链条罗拉、膨胀壁虎、自行轴挡、自行车异型件等)等各类异型、复杂非标件的冷挤成型,适用范围广泛。
- 推荐网络例句
-
I will endeavour to find you some assistance.
我尽力帮你找人帮忙。
-
At first I only know bruck is the idol of American younglings, afterwards I returned back to Taiwan ,even in Beijing last year ,I saw her poster everywhere, I was so surprised at her charm.
起初我只晓得布鲁克雷德丝是美国少男少女崇拜的偶像,后来回台湾,甚至去年在北京,居然也四处看见她的海报,才惊讶她的魅力之大。
-
Ah may dee:You are chinese living in a democratic country.
你是居住在民主国家的中国人吧。