轴螺栓

In one embodiment, a bolt with a jam nut is adjusted to position the shaft precisely.

在一个实施例中，对一个设置有防松螺母的螺栓进行调节，以使轴精确地定位。

To box joint, bolts fastness should start from symmetrical line to outside.

对箱形接头，应从平面两对称轴螺栓群中间顺序向轴外侧对称进行紧固。

The company's bolt, stud, nuts, screws, washers, ring, pin, key and shaft parts largest category of products, are strictly implementing the country's standards organization specializing in the production.

公司的螺栓、螺柱、螺母、螺钉、垫圈、挡圈、销、键及轴类零件大类产品，都是严格贯彻国家的标准组织专业生产。

Install the straps and bolts to hold the propeller shaft to the yoke.

安装扣夹和螺栓，将传动轴固定到轴轭上。

Puts in the electrically operated installment together the valve lever together with the key in the output axle hole, the valve coupling and electrically operated installment coupling spiral Kong Ru has the deviation to be possible to move slightly the handwheel to cause its correspondence, afterwards

将阀杆连同键一起放入电动装置的输出轴孔内，阀门连接盘与电动装置连接盘螺孔如有偏差可以微动手轮使其对应，之后将阀门连接盘与电动装置连接盘用螺栓紧固。

CNC surrounding attachment: all kinds of holders, body, chuck, chuck handle, adjustable boring hole, and tapping devices, BT pull bolt head, Tool Cart, spindle cleaning rods, lock knife blocks, all kinds of Z-axis settings Miriam, 3D form, eccentric type, photoelectric devices, such as edge finding.

CNC周边附件：各式刀杆、本体、夹头、夹头柄、可调式搪孔器、攻牙器、BT螺栓拉头、刀具车、主轴清洁棒、锁刀座、各种Z轴设定仪、3D表、偏心式、光电式寻边器等。

S Bolt, stud, nuts, screws, rivets, washers, ring, pin, button and Shaft Product categories are strictly implementing the country's standards organization specializing in the production.

公司的螺栓、螺柱、螺母、螺钉、铆钉、垫圈、挡圈、销、键及轴类零件大类产品，都是严格贯彻国家的标准组织专业生产。

Remove the universal joint strap bolts at the pinion shaft yoke.

在小齿轮轴轴轭处拆卸万向节扣夹螺栓。

The faults include the fracture of saddle support mat , the breakdowns of saddle support bolt and pin spindle.

其中，鞍座底板断裂、鞍座连接螺栓和销轴断裂，通过断口形貌和受力分析，判断故障原因为典型的疲劳断裂；大小齿面磨损变形严重是齿轮硬度不足、齿面接触应力超过材料抗剪屈服极限及润滑方法不当造成。

The faults include the fracture of saddle support mat, the breakdowns of saddle support bolt and pin spindle. Based on the analysis on the fracture and surface, the fault causes are analyzed, for the conclusions of the normal fatigue fracture, as well as the deficient gear hardness, higher contact stress of tooth face than the yield limit under shear of material and improper lubrication method, which bring serious abrasion deformation of tooth face.

其中，鞍座底板断裂，鞍座连接螺栓和销轴断裂，通过断口形貌和受力分析，判断故障原因为典型的疲劳断裂；大小齿面磨损变形严重是齿轮硬度不足，齿面接触应力超过材料抗剪屈服极限及润滑方法不当造成。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。