轴螺栓

The behaviour of these bolts, when fully grouted in resin, was investigated under axial and shear loading.

这些螺栓行为，当充分地填水泥在树脂，被调查了在轴向和剪装货之下。

Install differential case and dummy bearings in axle housing and tighten retaining cap bolts.

在轴壳内安装差速箱和模型轴承，并紧固固定帽螺栓。

The connecting pin axle, firm screw, screw, open pin should use the special components of the production factory.

各部件之间的连接销轴、紧固螺栓、螺母、开口销必须使用厂家的随机专用紧固件，不得随意代用。

And we has also accumulated original and mature experience in designing, manufacturing and assembling of bolt tightening system, press riveting and welding system, automobile seatbelt assembling special machine, pin and shaft press installing machine, transplanting machine, aerial material flow line, material flow line, lifting equipment, balance crane, fixture etc.; To meet its clients' demand, Congyu has independently developed many sets of special machine of high technology and great difficulty, which involves the clearance detection, angle control, sealing test, torque control and displacement control etc.

并在螺栓拧紧系统、压铆焊接系统、汽车安全带装配专机、销轴压装机、移栽机、空中物流输送线、物流输送线、提升机、平衡省力装置、各种产品的工装夹具等方面有独到成熟的设计、制造及组装经验；应客户要求独立开发出多套间隙检测，角度控制，密封性检测，扭矩控制，位移控制等高技术、高难度要求专机，在此基础上，不断创新并开发了清洗机等新产品和太阳能新领域，并为太阳能行业开发了自动上下料机、酸碱清洗机和自动插片机，接线盒涂胶机，自动裁切机，测试分选机等一系列生产和测试设备。

AFTER THE OWNERSHIP TRANSFER,IN ORDER TO STRENGHTEN THE MANUFACTURING CAPABILITY,THE COMPANY PURCHASED MANY NEW EQUIPMENTS LAST YEAR,THERE ARE CNC LINE CUTTING MACHINE,CNC STATOR COIL WINDING MACHING,CNC SPOT WELDING MACHINE,BELT SAW CUTTING MAHCING,HEATTREATMENT MODIFIED EQUIPMENT,500T FUEL PRESSER,CNC LATHE,STATOR AND ROTATOR LIQUER IMMERSION AND DRYING PRODUCTION LINE,SINGLE BOLT PRESSER,ARMATURE PRODUCTION LINE,STARTER ASSEMBLY AND TESTING LINE,LIQUER SPRAY PRODUCTION LINE,GERMANY TOX COMPANY PUNCHING AND CONNECTING FACILITY AND GERMANY NUT FASTENING FACILITY,AND WE ALSO PURCHASE THOSE ADVANCED TESTING FACILITIES SUCH AS THE DOMESTIC MOST ADVANCED COMPREHENSIVE TESTING UNIT,THREE DIRECTION HIGH AND LOW TEMPERATURE CHANGE AND VIBRATION TESTING UNIT,HIGH TEMPERATURE TESTING BOX.

企业转制后，为提高产品制造能力已购置生产设备：数控线切割、数控定子绕线机、数控点焊机、带锯床、热处理调质设备、500吨油压机、数控机床、定子、转子浸漆干燥线、单螺杆空压机、电枢生产线、起动机总装及试验线、喷漆线、德国TOX公司冲压连接设备和德国的螺栓紧固设备。试验设备：购置目前国内最先进的起动机综合试验台、三轴向高低温交变振动试验台、高温试验箱等试验设备。

Dome valve used to check all fasteners, in particular, to ensure that the valve body and the axis fixed dome bolts are tightened.

圆顶阀使用时必须检查所有紧固件，尤其确保阀内固定穹形体和轴的螺栓已紧固。

This paper applies nonlinear finite element method to analyze the behaviors of connections under cyclic load at fist time. Contact elements are set between end plate and column flange, screw cap and neighborhood plane, bolt bar and hole. After verification of FEM, more than 50 species of 10 series are computed.

主要研究了端板尺寸，柱的轴压比，强柱系数，梁端剪力，柱翼缘和腹板尺寸、宽厚比，螺栓的级别、大小、数量、预拉力和排列方式，连接抗滑移系数，端板加劲肋以及柱腹板加劲肋，材性，梁柱截面尺寸效应等对连接滞回性能的影响。

Head section : to include 400mm dia.lagged pulley,50mm dia.shaft ,ball bearings ,motor mount,assembled on channel frame to bolt to intermediate section of conveyor.

头部部分：包括直径400毫米的后滑轮，直径50mm的轴，球轴承，电动机安装，中间一段输送轨道框架用螺栓。

Flange joint bolt is just put in from the side of flange joint component, nut screw in from the side of flange of coupling.

法兰连接螺栓只能从被连接构件的法兰侧放入，螺母从联轴器的法兰侧拧入。

In the present study, through using non-linear three dimensional finite element analysis, considering the contact in flange to nut and flange to gasket, we accurately computed the stress distribution in the flange joint in the normal work condition.

采用ANSYB软件，应用三维有限元技术，考虑了垫片的非线性和法兰和螺母、垫片的接触问题，并且采用了螺栓预紧单元，准确计算出法兰连接在承受内压、轴向力和弯矩外荷载时的应力分布。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。