轴螺栓

Abilify West Canton Electrical Equipment Co., Ltd. is mainly machining, specializing in nested cone pulley, multi-wedge belt wheel, belt wheel, coupling, sprocket, gear, bulging tight connection kits, bolt kits, lock sleeve, welding kits, flange and industrial belts, such as technology research, development, manufacture of the modern enterprise.

广州阿立西机电设备有限公司是以机械加工为主的，专业从事锥套式皮带轮、多楔带轮，同步带轮、联轴器、链轮，齿轮，胀紧联结套，螺栓套，锁紧套，焊接套，法兰盘和工业皮带等技术研究、开发、制造的现代化企业。

Those are 3/8-16 bolts going into the countershaft.

这些都是3/8-16螺栓要到副轴。

Should be regularly checked relevant keyway, coupling and fixed bolt wear.

应定期检查相关键槽、联轴节和固定螺栓的磨损情况。

Planet reduction shown in figure 6. Loose nut 6 "nut + washer + anti-loose nut". The explored view is Adjust torque 350~400N.m, rotate hub 13 at the same time. 5 and a radial force F=70N crease, hub can rotate free. Then fix lock washer into nut 6, fasten loose nut with torque 400N.m and make spacer control 0.05~0.15mm.

调整时，用 350~400N.m 力矩旋紧螺母 6，同时转动轮毂 13，使两轴承处于正确位置，然后，稍旋松螺母 6，在轮辋螺栓处施加一个切向力 F=55N.m，此时轮毂应能自由转动，然后装上止动垫片 5，将其卡爪折入螺母 6 的防转槽内，再用 400N.m 的力矩旋紧防松螺母，使轴向间隙控制在 0.05～0.15mm 之间。

At the same time, the relationship between screwing length and axial stress distribution of bolt screw thread is studied, which offers reference to the design of nut height.

文中还对旋合长度对螺栓轴向应力分布的影响也进行了研究，为螺母高度的设计提供了参考。

What I'm doing here is casting in a brass collar and setscrew and a simple straight shaft instead of the hooked one.

什么我在这里做的是铸造在一个黄铜衣领和紧固螺栓和一个简单的直轴不是该迷上了1。

The torsion coefficient of bolting is tested with the intelligentized axial force tester and high precision torque spanner, to guarantee the data result veracious and reliable

螺栓连接副扭矩系数测试采用先进的智能轴力检测仪和高精度扭力扳手，保证测试数据准确、可靠。

Unbolt the shaft coupling bolts.

拧开联轴器螺栓。

In another embodiment, a tee bracket is anchored to a hoistway wall, and a jack bolt with shims is used to adjust the vertical placement of the long beams that support the elevator car frame and therefore the shaft.

在另一实施例中，一个T形托架被固定到一个通道壁上，用设置有垫片的调整螺栓来调整长横梁的垂直位移，该长横梁支承着电梯座舱框架，从而也支承该轴。

The simulation results show that this method can reduce maximal axial stress by more than 5%, and it observably improves stress distribution.

仿真结果表明，此方法可使螺栓轴向最大应力值降低5%以上，并有效地改善了应力分布。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。