轴线

2 V-belt adjustment 4.2.1 pulley in the center of the two vertical force F imposed on the Triangle Two V-Pulley plane dislocation Two pulley axis angle is not parallel Adjustment method according to the above adjustment, the operation a few days, using the same method again adjust.

4.2 三角带的调整 4.2.1 在两带轮的中心位置垂直于三角带施加力F 两V型带轮平面错位两个皮带轮轴线不平行夹角为按上述调整方法调整后，运转数日，用同样的方法再次调整。

The slim Muslim reached his climax when he found the axis of the galax y.

苗条的穆斯林在发现银河的轴线时达到了顶点。

3 Indicator error calibration:示值误差校准: Take turns place the standard gauge blocks with measure 10mm,20mm,30mm,40mm,50mm in the middle of plane measure heads ,adjust the gauge block position , make the center plane and measure staff axes plane touch with gently, after tranquilization, read the display result .

依次将尺寸为 10mm，20mm，30mm，40mm，50mm 的标准量块放入平面测头之间，调整量块位置，使其中心面与测杆轴线面轻轻接触，待稳定后，读取显示结果，其示值误差应在±0.5um 内为合格，否则停用修理(每次测量块时，要重新清零)。

Instantaneous motions of the end effector of the typical industrial serial 6-DOF and 5DOF robots are also studied using reciprocal screw theory, The constrained and permitted motions at special configurations are given. Furthermore, the satisfied conditions for the special configurations are discussed, and in the reference coordinate system general expressions of the reciprocal screw and existed motion screw and the subspaces of the permitted rotational axes are obtained under all circumstances at special configurations.

本文中还用反螺旋理论研究了六自由度和五自由度工业机器人的瞬时运动，给出了它们在正常位形和特殊位形下的受约束的运动和存在的运动，以及它们在所有运动参数的不同组合下的反螺旋及存在运动螺旋系的一般表达式和转动轴线存在的子空间。

The discrete mathematical models of the roundness and cylindricity EST are established; the mathematical models of the generating line straightness, axis straightness, coaxality, circular run—out and total run—out error of the revolution workpiece are put forward and established first based on the EST; the method about how to sample and to process sampling data are given when these models are applied to measure workpleces.

其主要内容是：针对长期以来国内对回转误差运动的有关定义的争论，对回转误差运动的本质进行了讨论，进一步明确了静心与静轴，动心与动轴的概念，并对此进行了数学推导，给出了相应的数学模型；统一了"平动说"和"瞬心说"关于回转轴线的定义，指出了两种学说各自的力学基础和它们的一致性。

The duty of the drame and the music which was give by the subject was accomplished by three elements used in this dissertation as following:the musical theme"La Roi S'amuse"(from the opera"Rigoletto")was the center clue;the forming precess of the three main characters (Rigoletto、Duke and Gilda)was the major may to interprete the drama subject; meanwhile, their own Arias were used to rebuild the musical figures; and the chorus between each of them was the main means to put forward the plot of the drama.

本论文以歌剧《黎戈莱托》的主题"诅咒"作为主轴线，以歌剧中三个主人公(黎戈莱托、曼图阿公爵、黎戈莱托的女儿吉尔达)在歌剧中各自音乐形象的塑造过程作为对歌剧主题诠译的主要手段，同时又以他们各自在歌剧中的咏叹调作为塑造音乐形象的主要方式，以他们相互之间的合唱作为歌剧情节向前发展的重要方式，从而完成歌剧主题所赋予的戏剧任务和音乐任务。

Sometimes put gradienter into monlchamus tuhung roll and bucket roll, check whether the monlchamus road and sea and nano-imprint lithography drums of oxial parllel.

有时还给把程量仪放到墨斗辊和水斗辊上，查抄墨路和旱路是否与压印滚筒的轴线交错。

The paper mainly discusses the research on the measuring instrument of gun barrel axis Straightness, which is based on image processing.

本文主要论述了基于图像处理的炮管轴线直线度测量仪的研究。

So we take measuring instrument of gun barrel axis Straightness as object of research.

基于此，本课题选择炮管轴线直线度测量仪为主要研究对象。

Cut a grape in half along its vertical axis leaving a tiny bit of skin linking the two halves.

沿着葡萄的垂直轴线把葡萄截成两半，并留下一点儿连接两半儿的葡萄皮。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。