轴线

It is determined that the pitch cone of honing wheel depends on the number of teeth in the honing wheel and the angle between the common normal of pitch cones and the plane parallel to both gear and honing wheel axes.

论文摘要：分析了基于交错轴传动的珩齿原理，导出珩磨轮与被珩齿轮在啮合点处的相对滑动速度的数学模型，根据该数学模型可以判定，珩磨轮的节锥面由珩磨轮齿数以及公法线和与珩磨轮及被珩磨齿轮的轴线平行的平面的夹角两个参数所确定。

A design method of non-perpendicular pitch cone of the honing wheel is presented in this article. By adjusting the distance from the contact point of pitch cones to the axis of honing wheel, the relative velocity between pitch cones is ensured to be in the direction of the tooth trace of the gear.

提出了用于珩磨螺旋锥齿轮的非正交珩磨轮节锥面的设计方法，通过调整节锥面切点到珩磨轮轴线的距离，保证了节锥面之间的相对速度恰好沿着齿长方向。

Analyzing the honing principle of spiral bevel gears based on crossing-axis transmission, the mathematical model of the relative sliding speed of the contact point between honing wheel and gear is achieved. It is determined that the pitch cone of honing wheel depends on the number of teeth in the honing wheel and the angle between the common normal of pitch cones and the plane parallel to both gear and honing wheel axes.

分析了基于交错轴传动的珩齿原理，导出珩磨轮与被珩齿轮在啮合点处的相对滑动速度的数学模型，根据该数学模型可以判定珩磨轮的节锥面是由珩磨轮齿数、公法线和与珩磨轮轴线平行的平面夹角所确定。

This method is using two times conformal transformation method and mirror theory to calculate the characteristic impedance.

这种方法是采用两次保角变换结合同轴线特性阻抗公式进行特性阻抗计算。

Another new spatial 3-RPS parallel pyramid manipulator mechanism is studied. The principal screws of this mechanism under three different configurations are identified by means of the conic section and the quadric degenerating theory, respectively. The planar conics representing the relations between the pitches of the output twists and the three linear inputs are described, and the three-dimensional distribution of the axes of all the twists with the same pitch is illustrated under each of the configurations.

研究了另一种新的空间三自由度3-RPS并联角台机构，分别用二次曲线和二次曲面分解法识别该机构在三种位形下的主螺旋，绘制了其在每种位形下的输出运动螺旋的节距与输入之间的平面图以及具有相同节距的所有运动螺旋轴线在每种位形下的空间分布的立体图。

In the other words, the influences of the winding's current cannot be think about by simply add these influence elements of these windings, the inductance of every winding becomes a complex equation which connected with the currents of all the windings and the permanent magnetic magnetic-force.

永磁磁动势的大小不变，但是转子位置改变时，对各相绕组的轴线的磁通路来说，永磁磁动势的作用便不一样，因此永磁磁动势的影响可以用电感与转角有关来描述。

Secondly, based on the research of the fabric"s contexture characteristic, the author puts forward using the convex shape as yarn"s section, builds the yarns dimensional geometry model and axes equation of warp and weft. Establishes the illumination model which is fit for fabric with illumination theory.

在研究织物组织模拟的基础上，提出以凸透镜形作为纱线截面，建立了相应的纱线空间几何模型和经、纬纱轴线方程；利用光照理论，结合织物的特点，建立了适用于织物的光照模型。

The coaxial impedance convertor plays a very important role in the field of high power microwave.

在高功率微波应用中，同轴线的阻抗匹配十分重要。

A curve coordinate system which is suitable for variable height curved box-girder were established.

当曲轴线半径与箱梁宽度比小于10时，必须考虑曲率沿横向变化的影响。3。

The rectangle shaped member mentioned by this article is a prefabricated one for the internal construction of circular tunnel, and is located along tunnel axis line, to be lifted into place by a dedicated crane onboard the shield machine in synchronised manner, followed by placement at both sides of tunnel, of ballast block, or in-situ cast members, corbel, pavement slab and the like.

由于隧道比较长，为节约工期，在盾构机推进的同时，隧道的内部结构也跟进施工，本文所叙述的口字型构件是圆隧道内部结构中的预制构件，它位于圆隧道的中心轴线位置，在同步施工中由盾构机上的专门起重机吊放入位，再于两侧施工压重块、牛腿、路面板等现浇结构。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。