轴箱

At the end of the analysis, it is suggested that exerting the elastic and damping restriction on the afterbody of the headstock was the best reasonable measurement.

通过各参数的比较分析，从而得出在系统动响应最小情况下，在主轴箱尾部施加弹性阻尼约束是最佳的改进措施。

The mainly working elements are: crankshaft and clamp are built on the imovable table-board. The headstock has aiguille and it follows dragging board to come true the boring athletics.The landscape orientation of dragging board, the up and down sport of shaking-arm and the running of dragging board turn up the modulating of working station.

其大体工作原理如下：曲轴和夹具安装在固定不动的平台上，装有钻头的主轴箱随进给拖板实现钻削进给运动，工作位置的调整是通过大拖板横向运动、摇臂的上下运动、摇臂的转动来实现的。

The unified formula results from the revolution and translational movement of the coordinate axis.

利用坐标轴的旋转和平移，导出了组合机床主轴箱多种传动形式下传动轴坐标计算的统一公式。

The early detecting and judging methods of axle box bearing failure are presented.

介绍了SS8 型机车轴箱轴承故障早期发现和判断的方法，分析了故障原因，提出了预防措施。

The solution could be easily and efficiently implemented through improvement on the design of locomotive axle box linkage.

通过改进机车轴箱拉杆设计可以简单有效地实施这一方案。

And productivity and calculate the card bore and make the lathe up to design including processing the process picture of the part, processed sketch map, lathe to contact size picture and and the calculated card of productivity, named " three pictures and one calorie " that usually spoken are designed; Many axle case part is it include many axle case design primitive drawing, main shaft choice and power calculate, design of transmission and calculate, etc., structure of form that basis pursue mainly to design.

粗镗组合机床总体设计包括被加工零件工序图、加工示意图、机床联系尺寸图和生产率计算卡，即通常所说的&三图一卡&设计；主轴箱部件设计主要包括主轴箱设计原始依据图的绘制、主轴结构形式的选择及动力计算、传动系统的设计与计算等。

And productivityand calculate the card bore and make the lathe up to designincluding processing the process picture of the part, processedsketch map, lathe to contact size picture and and the calculatedcard of productivity, named " three pictures and one calorie " thatusually spoken are designed; Many axle case part is it include manyaxle case design primitive drawing, main shaft choice and powercalculate, design of transmission and calculate, etc., structure ofform that basis pursue mainly to design.

粗镗组合机床总体设计包括被加工零件工序图、加工示意图、机床联系尺寸图和生产率计算卡，即通常所说的&三图一卡&设计；主轴箱部件设计主要包括主轴箱设计原始依据图的绘制、主轴结构形式的选择及动力计算、传动系统的设计与计算等。

When the spindle box cutter left Move right back to the workpiece, the rotary table 90 degrees, and then the left spindle box again.

当主轴箱右移退回到刀具离开工件后，工作台回转90度，然后主轴箱再次左移。

This article elaborated a 12 level of rotational speed C6132 horizontal lathe headstock design process, the headstock uses to support the main axle and to cause it revolving.

本文阐述了一个12级转速的C6132卧式车床主轴箱的设计过程，主轴箱用以支撑主轴并使之旋转。

This thesis combination machine for design processing many stalks the box ten screw threads of rights the bore bed.

车床主轴箱箱体右侧10-M8螺纹底孔组合钻床设计摘要：本论文为加工主轴箱箱体右侧十个螺纹底孔的组合钻床的设计。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。