轴的

Armatures originally produced with a solid fill epoxy coating that have not been resoldered or reshafted do not need revarnishing.

原来生产的有环氧层的电枢没有重新锡焊和再装轴的不必再浸漆。

The main controller is PLC programmable logic controller in the control system. A position control module, which has linear interpolation and circular interpolation of two axises, process shaping of flange seal-face and seal- groove. In order to operate inconveniently, the portable handling box was designed to operate the machine tool in a distance.

机床的控制系统采用PLC可编程控制器为主控制器，并带一个位置控制模块，它可实现两个轴的直线或圆弧插补功能，实现法兰端面和梯形槽的成形加工。

In this study, a spur gear coupled theory combined with a spinning composite flexible shaft theory, is used to develop a double spinning composite shafts model that are containing coupled by spur gears.

中文摘要本文主要目的，在结合复合材料旋转轴的理论与齿轮联结理论，导出含齿轮联结效应之双复合材料轴的运动方程式，并探讨系统的振动特性与暂态响应。

By implementing immersion lithography, Matsushita/Panasonic has achieved the smallest minimum metal patterning that we have seen to date, at 67-nm M4 half-pitch.

由于使用了浸入式光刻，松下实现了至今为止最小的金属布线，第四金属层半节距为67nm（两条布线中轴的距离为节距，按布线宽与隔离空间各一半算的话，布线的实际宽度为半节距）。

Shaft's center line should be horizontal and vertical, can be used after normal iron level scale machining center vertical and horizontal surface inspection.

泵轴的中心线应与水平垂直、可用普通铁水平尺在经过机械加工的与中心垂直的水平面上检查。

Based on lubrication analysis of journal bearing, the stress distribution of shaft was calculated by using film pressure that calculated as boundary condition of load.

在轴承润滑分析的基础上，将得到的轴承油膜压力作为载荷边界条件，计算了轴的应力分布。

You have to do the measurings only when both the digital comparator and the axis in measure focus bar are perfectly steady and exactly in the same points.

你不得不做测量，当数字比较器和轴的聚焦条在同一点是确定的、稳定的。

As a kind of precisely inertial instrument, the orientational accuracy of the north-seeking system is decided by the accuracy of the gyroscope it used to a large extent.

在本文中我们研究的这种磁悬浮陀螺寻北仪，就是通过采用自适应控制方法，利用磁悬浮技术实现对单自由度陀螺框架轴的无摩擦悬浮，旨在得到更高的寻北精度，同时提高定向速度。

Nevertheless, in this gure the horizontal axis of the resultant proles are converted to surface positions varying from zero to expected feeds of 0.4, 0.6, 0.8 and 1.0 mm/rev for better comprehension.

然而，在这个数字横轴的由此造成的个人资料将被转换为表面的立场不同从零到预期饲料0.4 ， 0.6 ， 0.8和1.0毫米/恢复为更好地理解。

Two pairs of chutes and holes on the cleaning base and the brushes form the double chute swing mechanisms by the connection of an axis and cause the brush to cling to the wall surface to clean by the friction feedback, thus achieving effective cleaning when walking error occurs and the pipe section changes, furthermore, the larger the friction on the wall surface is, the larger the forward pressure on the wall surface is, therefore, the dirtier the wall surface is, the higher the cleaning efficiency is.

清扫底座与刷子夹上的两对滑槽和孔通过轴的连接形成双滑槽摆动机构，并通过摩擦力反馈使得刷子能够紧贴壁面进行清洗，从而在出现行走误差和管道截面变化时都能够有效清洗，并且壁面摩擦力越大刷子作用在壁面上的正压力越大，因此壁面越脏时清扫效率越高。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。