轴杆

The part fastened to the driving shaft is truncated cone and its diameter is much smaller than that of the part fastened to the ring nut and which regulated grinding.

固定在驱动轴上的部分是被切去顶端的圆锥形，它的直径比固定在螺杆上的那个磨片小很多。

According to deformation features of tube rolled by SPG mill, The formulas are deduced to calculate geometry parameters of instantaneous deformation zone, flow, slip and deformation.

全面分析了影响力参数的各种因素，提出了关于力参数的计算方法，并对影响轴向力的三个主要因素（轧制半径、摇杆参数和辊颈半径）做了定性、定量的研究，提出了这些参数的确定原则及计算方法。

It is a screw gearing in which the worm and wheel are in contact with a straight line.

提出了以这种蜗杆为砂轮实现无轴向进给磨削圆柱齿轮的原理与方法。

Worm wheel and worm —Used to transmit the turning force and rotary motion between two perpendicular axes.

蜗轮蜗杆用于传递两垂直交叉轴间的动力和转速。

The piston is attached to the top of a connecting rod by a pin,called a piston pin or wrist pin.the bottom of the connecting rod is attached to the crankshaft.the connecting rod transmits the up-and-down motion of the piston to the crankshaft,which changes it into rotary motion.the connecting rod is mounted on the crankshaft with large bearings called rod bearings.

这个活塞被一个叫活塞销或轴颈销的销子连接在连杆的上部。连杆的底部被连接在曲轴上。连杆把活塞的上下运动传递给曲轴转变成旋转运动。连杆通过一个大的叫做杆轴承的轴承（其实就是滑动轴承，分成两个半圆轴瓦）安装在曲轴上。

Also, some joysticks can have their handle twisted left and right to control the yaw axis.

如果你的摇杆没有偏航轴，你可能就需要一套脚舵来控制偏航，这也会真实很多。

150HP-300HP screw air compressor rotor is the German GHH-RAND joint shaft type unit,adopts the third generation asymmetrical dentate 5:6 rotors,The major axis is more reasonable than the choice, the tangent speed of rotors is only 30-36m/s, is far lower than that———60m/s of common air compressors, it keeps 0.003INCH between rotors that will not abrase forever, the space between teeth dropping variance is small, so the backflow loses is slight, Enhances10-12% kf the efficiency compared to the 4:6 dentate, save power 20%, adopts the Swden SKF bearing.

150HP-300HP）螺杆机转子为德国GHH-RAND联轴式机组，采用第三代非对称齿型为5：6的转子，长径比选择合理，其转子的切线速度仅为30'36m/s，远低于一般空压机60m/s 的切线速度，转子之间保持0.003INCH间隙永不磨损，齿间落差小，故回流损失小，比4：6齿型提高效率10-12%，省电20%，采用瑞典SKF轴承，极大延长了主机的寿命。

Br/br/Adopts the GHH-RAND remarkable mainfrane br/(150HP-300HP) screw air compressor rotor is the German GHH-RAND joint shaft type unit,adopts the third generation asymmetrical dentate 5:6 rotors,The major axis is more reasonable than the choice, the tangent speed of rotors is only 30-36m/s, is far lower than that60m/s of common air compressors, it keeps 0.003INCH between rotors that will not abrase forever, the space between teeth dropping variance is small, so the backflow loses is slight, Enhances10-12 kf the efficiency compared to the 4:6 dentate, save power 20, adopts the Swden SKF bearing.

采用GHH-RAND卓越主机br/（150HP-300HP）螺杆机转子为德国GHH-RAND联轴式机组，采用第三代非对称齿型为5：6的转子，长径比选择合理，其转子的切线速度仅为3036m/s，远低于一般空压机60m/s 的切线速度，转子之间保持0.003INCH间隙永不磨损，齿间落差小，故回流损失小，比4：6齿型提高效率10-12，省电20，采用瑞典SKF轴承，极大延长了主机的寿命。

Driving system is one key of it, and it needs big torque and endures biggish shaft power.

传动系统是双螺杆磨浆机的关键部件，要求输出较大的扭矩，并承受较大的轴向力。

A rod, reel and bag full of different lures us above mention your pliers and boga grip.

一杆、 轴和袋充分的不同诱饵我们以上提及你钳子和 boga 掌握。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。