轴杆

The climbing load design method for motor vehicle driving axle half shaft is a computational method recommended by IVECO,which is formed on the basis of driving torque required for a motor vehicle in climbing a 18% gradient of slope and combined with approximate fatigue limit of material.

汽车半轴杆径的坡道载荷设计法，是在IVECO推荐的汽车在18％坡道上所需驱动力矩基础上，融合了材料的近似疲劳极限而成的计算方法。

The circular top part of a capstan, used to hold bars for turning.

绞盘头绞盘的圆形顶部，用于套住轴杆，使之旋转

From the problem of the collision between small ball and homogeneous pole, the rules followed by different type of collisions are discussed, and the energy features of completely inelastic collision are summarized.

从小球与均质定轴杆的碰撞问题出发，讨论了不同类型碰撞所遵循的物理规律，总结了完全非弹性碰撞过程的能量特征。

Measured and recorded Records shaft / rod diameter, pore size and depth of the stuffing, and then water seal ring, stuffing box at the bottom to the top of the record the distance.

测量与记录记录轴/杆的直径、填料函孔径和深度，且当时用水封环时，记录填料函底部至顶部的距离。

Clean and check 1 slowly loosen the gland nut stuffing, packing the release of residual pressure of all components; 2 Remove all old packing, thoroughly clean axle / rod stuffing; 3 Check the shaft / bar have corrosion, dents, scratches or excessive wear; 4 Check whether there are other WATER POWER CONTROL VALVE parts burr, cracks, wear, they will reduce the packing life; 5 Check whether there is too much stuffing the gap, and the shaft / rod eccentric degree; 6 the replacement of defective parts larger; 7 Check the old packing, as BALANCING VALVES the basis of failure analysis to find the reasons for early failure of packing.

缓慢松开填料函的压盖螺母，释放盘根组件内所有的残余压力； 2）移去所有旧的盘根，彻底清洁轴/杆的填料函； 3）检查轴/杆是否有腐蚀、凹痕、划伤或过度磨损； 4）检查其他零件是否有毛刺、裂纹、磨损，它们会减少盘根的寿命； 5）检查填料函是否有过大的间隙，以及轴/杆的偏心程度； 6）更换有较大缺陷的零部件； 7）检查旧盘根，作为失效分析的依据，球阀以找到盘根早期失效的原因。

Puet控制杆mailes放任非属欧银杆因子 Villard's reasoning isn't entirely clear, but apparently he assumed that at the wheel would always have four hammers on one side of the axle, and three on the other side, keeping it in continual unbalance.

维拉德的推理并不完全清楚，但显然他认为在方向盘总是有四个锤一方的轴，三的另一边，保持它在不断的不平衡。

For diameter 26mm axle bar of CK45 steel,when surface hardness is 54～ 62HRC,core maximum hardness is 32HRC and case depth is 3.8～5.3mm,it has an optim um combination of strength and ductility .

对φ26mm CK45钢轴杆，当表面硬度为54～62HRC，硬化层深度为3.8～5.3mm，心部硬度＜32HRC时，轴杆具有最佳的强韧性，获得了较高的静扭强度和扭转疲劳寿命。

The Flex-Hone tool should be securely held in a collet, chuck, or similar holding device. It is best to use the shortest shank possible for your application.

球头刷应该被安全地固定在筒夹、卡盘或其他类似的固定装置上，最好使用尽可能短的轴杆。

Economically Designed for Minimal Deadband- A splined end connection on the drive shaft allows lever clamping by most Fisher rotary actuators.

经济专为最小死区，在驱动器上花键轴杆结束连接允许大多数费舍尔旋转器夹紧。

The shear strength changed due to specimen enclosed in a membrance and frictional effect of loading ram can be neglected during deviatoric load was being applied.

在施加轴差应力时，橡皮膜之束制效应与轴杆之摩擦效应对砂土之剪力强度之影响可以忽略。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。