轴承座

The increment of the horizontal component of the force together with no change in direction makes the roll system steady.

保证辊系稳定的有效办法是让工作辊轴承座与支承辊轴承座之间受一个方向始终不变的水平力。

Horsing made of deep-drawn material cast on accurate mould.and automatically welded to pipe simultancously at both side.

轴承座 Housing 用深冲材料及精密金属模具加工制成的轴承座采用自动焊接方式同时焊接在钢管两端。

The ball bearing unit is possible working in the non-concentric condition with the maximum self-correcting angle of 2 degrees.

带座外球面轴承可在两轴承座不同心的情况下工作，最大自动调整角可达2o。

And within the help of ANSYS software, how housing thickness, plastic module of housing and oil film pressure gradient effects the bearing stress distribution is analyzed in this paper. The relationship between alloy tangential stress or radial stress or shear stress and oil film pressure or pressure gradient is also analyzed.

利用ANSYS软件分析了轴承座厚度、轴承座弹性模量和油膜压力梯度对轴瓦应力分布的影响，分析了轴瓦合金层周向应力、径向应力和剪应力的应力场与油膜压力及油膜压力梯度的关系。

The paper introduced in detail the machining scheme and quality control indexes Tangshan Dunshi Machine Company adopted for the key parts of 400mm roller press-bearing housing, head parts and annectent.

文章详细介绍了唐山盾石机械制造有限责任公司制造400mm 辊压机时，对关键结构件―轴承座，以及端部件、轴承座与上下机架组对后的加工工艺方案和质量控制指标。

They put forward that a new concept of open /closed compound pair,which is not only used to renewably synthesize restrict mechanism of bearing stand chock about aluminum foil mil...

提出开闭复合运动副新概念，重新综合铝箔轧机轴承座约束机构，解决了该轧机工作辊轴承座与机架窗口间更换轧辊必留间隙和在运行时须消除间隙的矛盾。

Bull gear and pinion gear are mounted in lower casing via bearing seat.

大小齿轮均采用渗碳淬火钢进行制造，并采用硬齿面加工方法加工而成，强度很高。小伞齿轮和大伞齿轮均通过轴承座装入下壳体中，两轴承座法兰下设有调整垫，用于调整齿轮副接触区的位置和齿侧间隙。

Mechanical seal assembly: In the dynamic and static loop mirror coating on the 20th floor cleaner lubricants; add lubricant bearing guided, first gently positioning ring static load bearing guide; longer shaft add the oil, the mechanical seal part of the dynamic ring gently into the shaft, the hand-push retractable seal ring should be able to freely (Note that dynamic and static part of the anti-ring to the assembly site to be in place).

机械密封装配：在动、静环镜面上涂一层洁净的20号润滑油；导轴承座抹上润滑油，先把静环轻轻定位装入导轴承座；再在泵轴上抹上润滑油，把机械密封的动环部分轻轻装渗透泵轴上，用手轻推密封环应能伸缩自如（注意动、静环部分的防转部位需装配到位）。

Mechanical seal assembly: In the dynamic and static loop mirror coating on the 20th floor cleaner lubricants; add lubricant bearing guided, first gently positioning ring static load bearing guide; longer shaft add the oil, the mechanical seal part of the dynamic ring gently into the shaft, the hand-push retractable seal ring should be able to freely (Note that dynamic and static part of the anti-ring to the assembly site to be in place).

机械密封装配：在动、静环镜面上涂一层洁净的20号润滑油；导轴承座抹上润滑油，先把静环轻轻定位装入导轴承座；再在泵轴上抹上润滑油，把机械密封的动环部分轻轻装入泵轴上，用手轻推密封环应能伸缩自如（注意动、静环部分的防转部位需装配到位）。

For locating bearing positions and CARB bearings insert a locating ring between the bearing outer ring and housing shoulder on the locknut side of bearing.

为将定位轴承和CARB轴承的位置定准，将一个定位环插放到轴承外圈和轴承座挡边之间、轴承锁紧螺母的一侧。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。