轴承

In this thesis, the contact point position between rib and roller was deeply studied and analyzed, it is one of the main reasons of causing temperature rise of freight train bearing.

本文就针对这一要求对引起提速铁路货车轴承温升的主要原因之一：挡边与滚子接触点位置进行了深入细致的分析和研究。

Does not allow a ferromagnetic impurities, and particles into the magnetic drive and vice friction bearings.

1不允许有铁磁杂质、颗粒进入磁力传动器和轴承摩擦副。

Smallest bearing friction, complex drive control and large inertia guarantee perfect synchronization.

最小的轴承摩擦、复杂推进控制和大惯性保证完善的同步。

While we're establishing our bearings, we're brought fresh fruit salad, a champagne cocktail and the morning papers.

虽然我们建立我们的轴承，我们带来了新鲜的水果沙拉，一杯香槟鸡尾酒和早报。

Producing and selling what we already have( bearing, pointer, thrust washer, water pump, piston, sleeve, crankshaft, fan blade, ball joint, tie rod, fuel pump and so on), LUKIA also manufactures products according to the samples or OE No.

生产和销售什么，我们已经有（轴承，指针，推力垫圈，水泵，活塞，套，曲轴，风扇叶片，球窝接头，拉杆，燃油泵等）， lukia还制造的产品，根据样本或光电号您所提供的。

But the strife is prolonged beyond its interest; except for the bearing of some few arguments on either side, nothing that is altogether new, after all, is adduced for or against, and it may be said that with Bossuet's work Gallicanism had reached its full development, sustained its sharpest assaults, and exhibited its most efficient means of defence.

但是，长期的内乱是超出其利益；除轴承争论的一些少数任何一方，没有什麼是完全新的，毕竟是引证支持或反对，而且可以说，与波舒哀的工作Gallicanism已经达到了充分发展，其最大持续攻击，并展示其最有效的防御手段。

On the process of identifying the Gapping of Main Journal Bearing of Engine, we used GONN and fuzzy system separately and successfully solved the main problem in fault diagnoses of engine through the two results.

在发动机主轴承间隙辩识过程中，直接使用GONN算法和该系统分别进行辩识，通过将两种结果相互补充，成功地解决了发动机故障诊断中的主要问题。

Includes floorstand with gate position indicator, handwheel, fittings and extension.

包括带有闸板指示器的地轴承架，手轮，连接件和加长件。

Commonly used products: Brass wire, including zinc line, polishing lines, filters, ion exchange resins, conductive block, wire mold, insulation board, guide pulley, bearings, water spray nozzles, descaling agent K200, KC12, eye discharge mode discharge brass, discharge chucks, belts as well as a strong magnet, clamp, charge plates, screws, etc. have the cash, and other great products: Tension brushless motor, sets up nose snakes belly, auxiliary sprinkler head, cluster-type sprinkler head Block, Block, and the mother spray, sprinkler head connected·, sprinkler head covered by panels, round round of vice-axis spindle, folder line wheels, power wheels, flow meter, electric plate fixed to the pad, round round, wire wheels, gears, axle win hearts catheter, vertical meter cable, pole lines, grounding line, guide line wheels, micro switch, on the nose, eyes mold base, the wheel seat, rectifier ring, nose mounting insulation, automatic threading catheters, eye mold base assembly, pressure gauge and chuck ER group, eyes fixed mold plate and so have the cash or stock.

常用产品：黄铜线、包锌线、抛光线、过滤器、离子交换树脂、导电块、导丝模、绝缘板、导轮、轴承、喷水嘴、除锈剂K200、KC12、放电眼模、放电铜管、放电夹头、皮带以及强力磁石、夹具、押板、螺丝等均有现货，其他非常用产品：张力马达碳刷、上机头蛇腹套、辅助喷水头、子母型喷水头喷座和母座、喷水头连接铜环、喷水头盖板、出线轮主轴副轴、夹线轮、强力轮、流量计、给电板固定垫、出线轮、引线轮、齿轮、出线轮轴心、导管、垂直度计连接线、极间线、接地线、引导线轮、微动开关、上机头、眼模座、滚轮座、整流环、机头绝缘固定座、、自动穿线导管、眼模座总成、压力表以及ER夹头组、眼模固定板等有现货或备货。

New multi—objectives function (including mill stand longitudinal stiffness, distribution coefficient of loaded pressure between rolls, weight of mill stand, rolling power, rolls loaded gap profile changeability of bending force, transverse mill stand stiffness of bending force, transverse mill stand stiffness of rolling load) multi—constraints (including rolls strength, spindle strength, backup roll bearing load, minimum rollable gauge, roll surface temperature rise) rolls system parameters optimization model of four—high cold strip mill is established, and programme for mill structural illustration creation on the platform of AutoCad designs is compiled. With this as basis, rolls system parameters of Yichang thin strip corporation's 1219 cold mill are calculated using SUMT (subsequent unconstrained minimization technology).

本文建立了以板形和板凸度控制特性为目标的四辊轧机多目标函数（包括轧机纵向刚度、辊间压力分布系数、轧机重量、功率、弯辊力对轧机辊缝形状改变能力、对弯辊力的横向刚度、对轧制力的横向刚度）、多约束条件（包括轧辊强度、接轴强度、支承辊轴承负荷、最小可轧厚度、轧辊温升等）的辊系参数优化模型，以此模型为基础，利用惩罚函数法计算了益昌薄板公司1219冷轧机辊系参数，编制了AutoCAD平台下的轧机结构示意图自动图形软件。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。