轴承

The main aim of this thesis is to study and implement the digital control system for magnetic bearing.

本文以有源磁轴承的数字控制系统为主要研究对象。

In the thesis work, digital control system is implemented with the advanced digital signal processor.

建立磁轴承系统并实现其数字控制系统是本论文工作的重要任务。

The dirtily fraught 'Born bad' with its slinky side winding riffs and pouting fuck you demeanour is a bearing down vibrant slice of gritty fuzzed out and mutated three chord candy pop that sounds to these ears as though it was fathered by early career Suicide.

肮脏地忧虑的'Born bad'以它苗条的旁边绕即兴重复段和噘嘴的fuck 您demeanour 是轴承下来充满活力的切片粗砂fuzzed 并且那听起来对这些耳朵的变化的三弦糖果流行音乐好象它由早期的事业自杀生了。

These deal with all aspects of bearing procedures, including handling of bearings, mounting, maintenance and inspection, dismounting and bearing storage.

这些处理各方面的影响程序，包括处理轴承，安装，维修和检查，拆卸，同时存储。

The result of experiment makes clear that the signal of displacement can be detected by using the excitation coil.

实验结果表明，利用磁悬浮轴承的励磁线圈可以检测出转子的位移信号，不需要设计专门的位移传感器。

IRIC arrogantly refused SVW's suggestion and SVW cost a whole day to coordinate between GE Beijing and Mr. IRIC, with SVW's persistent dissuasion IRIC finally agreed to have a measuring again and the readings showed that the deviation of the alignment data reached 2 mm, far beyond the specified standard 0.05 mm. If the wrong hadn't been corrected there would be serious consequence during the commissioning and damages to the bearings and seals would be inevitable.

但是IRIC坚决不同意，态度傲慢，我们花费了一天的时间同GE北京和IRIC进行之间协调，并积极说服，最终才同意再次测量一次，监测结果是对中数据偏差达到2mm，大大超出标准数据5丝，如果不纠正试车将会发生重大问题，轴承和密封都可能损坏。

The design target,operation conditions and main technical parameters of the 353130X2-2RZ double row cone roller bearing s are described.

介绍了353130X2—2RZ型双列圆锥滚子轴承的设计目的、运用条件及主要技术参数。

Entrusted to the structure of double pulley as shown in Figure 3, by the guide pulley, a small guide pulley, a fixed shaft and bearing components.

复式托带轮的结构如图3所示，由大导轮、小导轮、固定轴及轴承座组成。

Fixed occasional double pulley block fixed at both ends by bearings.

复式托带轮固定轴两端由轴承座固定。

Perforating spanner, tyre spanner, crowing spanner, spanner, crossing spanner, universal spanner, spark plug spanner, inner hexagonal spanner, bidirectional oil core spanner, ball puller, refined chain stripper, vent-pipe tools, bearing tools, valve tools, clutch tools, gear stripper, stripper, curving pole, connecting pole, slipping pole, spanning pole, striking spanner, striking sleeve, short sleeve, double-claw puller, trinal-claw puller, magnetoelectric machine puller, spring.

宁波市鄞州佳欣工具厂 Ningbo Yinzhou Jiaxin Tools Factory 4C72 穿孔扳手、轮胎扳手、撬杠扳手、T型扳手、十字扳手、万向扳手、火花塞扳手、内六角扳手、三爪双向机油芯扳手、球头拔卸器、精品拆链器、排气管工具、轴承工具、气门拆装工具、双向离合器工具、正时齿拆卸工具、拆卸器、撞批嘴、批咀、弯杆、接杆、滑杆、扳杆、冲击起子、冲击套筒、短套筒、二爪拉具、三爪拉马、二爪拉马、磁电机拉马、螺丝批。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。