轴承

Presented in this paper is a mathematical model for optimal construction design of the thrust bearing support in a large hydraulic turbine.

本文通过对大型水轮机推力轴承支架结构特点的分析，提出了大型水轮机推力轴承支架结构优化设计的数学模型。

With the technology of AMB is known and mastered gradually, AMB will be applied to these fields far and wide: aviation and spaceflight, vacuum technology, machine tool and tail-wagging engine, energy source and

随着主动磁轴承技术逐渐被人们认识和掌握，主动磁轴承将广泛地应用于以下领域：航空航天领域、真空技术领域、机床与高速旋转机械、能源交通等。

The mean value of work loads on a shaft bearing of swivel and rotary table is determined by basic principles of fuzzy theory, considering the loads' fuzziness and the requirement for reliability.

考虑钻机水龙头和转盘主轴承工作载荷的模糊性及可靠性要求，应用模糊数学基本原理求得平均计算载荷，从而计算出主轴承的模糊可靠性寿命。

The currency-used equations for calculating the life of the main bearings on rotary table and swivel take no consideration of all the affecting elements. The author offers thereby new equations that take an overall consideration of the load, rotary speed, lubrication, assembling, working environment, material and surface hadness.

针对现有文献给出的转盘和水龙头主轴承寿命估算公式对多种影响因素考虑不充分，与实际工况有一定出入的问题，推导出全面考虑载荷、速度、润滑、装配、工作环境和材料及表面硬度等多种影响因素，估算转盘和水龙头主轴承寿命的新公式。

The inner ring of the bearing has taked special heat treatment , the groove and the nearby can keep high hardness and make sure of the screw hole would not cracked as the stop screw standing the bigger short fastening. So enhanced the lifetime of the bearing.

轴承内圈经过特殊热处理，沟道及周边能保持较高的硬度，保证顶丝在用较大短紧固时，螺孔不会因硬度太高而开裂，从而大大提高轴承寿命。

The marine stern tube bearing is a special structure andcomplicated load sliding bearing, which is always under foullubricative state in real work, and always produces bad abrasion toget premature invalidation.

船舶尾管轴承是一种受力复杂、结构特殊的滑动轴承，它在实际工作中处于极其恶劣的润滑状态下，常常产生严重的磨损而导致尾轴承的过早失效，这对船舶安全航行和营运经济效益带来很大的影响。

First you need the boring for the shaft, then install the stern tube into the stern frame, next fit the gun-metal or white-metal bush.

首先要镗孔，然后安装尾轴管，接下来装炮铜或白合金制的轴承套，也叫轴承。

The first step is separating bearing one by one to be weighing, then the microcontroller decide whether current bearing is good or bad based on the weighing data from the balance, make the electric magnate move to distinguish the good bearing from bad ones.

这是称重法的必由之路；第二步根据称重天平串口传来的数据，经由单片机判断控制继电器动作，实现轴承的分拣。同时讨论了对关键部件，轴承排序机构上，中，下盖的材料选取及主轴与带传动的设计方案。

The advanced method is to use a new type of bearings are embedded in the seal groove, the groove depth than the standard bearings are slightly A42C Type Pound-Grade Low Lift Spring Loaded Safety Valve shallow point, and just fit in the intersection part, fill in the gap left by the outer ring flange.

该先进方法是用一新型有凹槽的密封圈嵌入轴承中，该凹槽深度要比标准轴承的稍浅点，且恰好适配于相交部分，填入外圈凸缘留下的间隙。

In most cases, this bearing outer ring A41C Type Pound-Grade Low Lift Spring Loaded Safety Valve locking mouth, and can not seal the resulting circular groove, leading many to be used in machine tool WA41C blanced bellows spring loaded safety valve spindle angular contact ball bearings can not be used as another host on the other bearings as filling grease.

大多数情况下，这种轴承的外圈带锁口，因而无法密封由此形成的环形凹槽，使得许多用在机床主轴上的角接触球轴承不能象用于别的主机上的其他轴承那样加注润滑脂。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。