轴承

The paper summrized lubrication technology and the selection of lubricant for rotary kiln, grate cooler, mill, conveyor mechanical equipment and large scale fan as following,(1)in rotary kiln, apply oil spoon of circulatory lubrication or pump forced oil supply system in the roller supporting mechanism and use (superscript #)680 high load industrial gear oil, and use lubrication method of idle oil wheel or spray in drive gear wheel and select solid lubricant which has high viscosity, strong adsorbability, good abrasion resistance in utmost pressure and lattic crystal structure,(2) in grate cooler, use immersion oil lubrcation in reducer and boiled oil centralized lubrication method in supporting roller and guide roller bearing, choose (superscript #)1 limit pressure lithium lubrcant grease,(3) in mill, use circulatory lubrication with fluxing oil station in drive mechanism and circulatory lubrication with high-low pressure fluxing oil station in main bearing and sliding shoe bearing and select N320 industrial gear oil.

文章全面总结了回转窑、篦冷机、磨机、输送机械及大型风机的润滑技术和润滑剂的选择。其中，(1)回转窑的托轮支承装置一般采用油勺供油的连续循环润滑方式或油泵强制供油系统，润滑油选用680重负荷工业齿轮油；传动大小齿轮的润滑一般采用带油轮或喷雾的润滑方式，润滑剂宜选用粘度高、吸附性强、极压耐磨性好、具有点阵晶体结构的固体润滑剂；(2)篦冷机中传动减速机的润滑一般采用浸油飞溅润滑；托轮，挡轮轴承的润滑一般采用干油集中润滑的方式，润滑脂一般选用锥入度310~340的1极压锂基润滑脂；(3)磨机中传动装置一般采用稀油润滑站循环润滑和冷却的方式；主轴承或滑履轴承的润滑一般采用高低压稀油润滑站循环润滑和冷却的方式，润滑油一般选用N320工业齿轮油。

The structure of the form of colorful products, including skateboards, cylindrical bearings, some bearing, joint bearings, flange bearings.

产品的结构形式丰富多彩，包括滑板，圆柱型轴承，部分轴瓦，关节轴承，法兰轴承。

When the flexible shaft~bearing system was excited with the second order frequency, the maximum oil pre

在二阶频率的正弦载荷作用下，弹性轴-轴承系统的最大油膜压力远大于刚性轴-轴承系统，而其最小油膜厚度则远小于刚性轴-轴承系统。

Engine work, if crude oil filter was a serious blockage of impurities, or due to low temperatures when the oil viscosity changes, the main oil缺油Road will be the engine will lose lubrication, this is very dangerous, especially in the main bearings and connecting rod bearings, if there is no oil will be burned, bearing alloy heat due to friction loss and even journal welded together, eventually forcing the engine to stop working.

发动机工作时，若机油粗滤器被杂质严重淤塞，或者由于气温低而机油粘度变大时，主油道就会缺油，发动机就会失去润滑，这是很危险的，特别是主轴承和连杆轴承，如果没有润滑油会烧坏，轴承合金会因摩擦发热而流失，甚至和轴颈熔焊在一起，最终迫使发动机停止工作。

SF-2 boundary lubricated bearings increase:Acid poly A with formaldehyde, with high wear resistance, bearing surface arrangement of the law must be fitted with a storage pit filled with grease, especially for high load low speed of rotation, rocking motion, and frequently borne, the opening and closing the difficult parts of the formation of lubrication in boundary lubrication conditions, long-term use without refueling and maintenance, where the fuel bearing life can be more extended, currently applicable to metallurgical machinery, mining machinery, hydraulic machinery, automobile parts, construction machinery, agricultural machinery.

SF-2加界润滑轴承：酸多聚甲醛一高耐磨性，轴承表面的法律安排，必须配备与油脂填补了蓄水坑尤其是高负荷低转速旋转，摇摆运动，并经常承担，开幕和闭幕的困难部分在边界润滑条件下，长期不加油和维修，那里的燃料轴承寿命可以更延长，目前适用于冶金机械，矿山机械，液压机械，汽车零部件，工程机械，农业机械使用润滑形成。

The physical model established takes into account the lubricating oil film, thrust bearing, runner and thrust head. The thermo elastic deformation of the thrust bearing and runner was analyzed based on ADINA program.

物理模型包括润滑油膜、推力轴承和镜板推力头，采用ADINA程序计算水口巴氏合金瓦和三峡弹性金属塑料瓦推力轴承和镜板推力头的热弹性变形，并对轴承性能的计算结果和测量结果进行了对比分析。

A herringbone gear corrects this thrust by neutralizing it,allowing the use of a small thrust bearing instead of a large one and perhaps eliminating one altogether

人字齿轮是用平衡的方法来抵消轴向推力的，因而允许选用轻系列轴承来取代重系列轴承，甚至可以完全取消推力轴承。

The process of elastohydrodynamic analysis combined with compliance matrix was described,and an elastohydrodynamic calculation was done using ORBIT as tools with compliance matrix on conrod big-end bearing of a 4 cylinder in-line diesel engine.

介绍了结合柔度矩阵的轴承弹流分析流程，并针对某直列四缸柴油机连杆大头轴承，应用轴承设计软件OR-B IT结合有限元软件生成的柔度矩阵进行了弹流润滑计算分析。

In the design of radial internal clearance for four row tapered roller bearing with tapered bore,Finite Element Analysis method is used to analyze and calculate the expanding difference between inner rings resulting from interference fit.

在圆锥孔四列圆锥滚子轴承径向游隙的设计中，利用有限元分析方法对过盈配合而导致的内圈膨胀量的差异进行了分析、计算，得到了该类轴承的各列径向游隙相互差，为轴承的游隙设计提供了依据。

We have been committed to manufacturing high strength aut tomobile clutch bearings,steering knuckle pin bearings , steering knckle pin repair patch and automobile transmission bearings.

十几年来企业致力与专业生产制造高强度汽车离合器轴承、转向节主肖轴承和主肖修理包及变速箱轴承等汽车部件。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。