轴套

A dissertation is made on the structure characteristics and the operating principle of the die casting mould.

为此设计了一种特殊的轴套压铸模具，论述了模具结构特点和工作原理。

Expeller, pressure-relief cover and shaft sleeve are made of wearable material, which are of low maintenance, long life

付叶轮、减压盖、轴套均采用耐磨材料制造，维修量少，使用寿命长，使整机平均无故障工作时间MTBF大大提高。

Expeller, pressure-relief cover and shaft sleeve are made of wearable material, which are of low maintenance, long life for use and greatly improve MTBF

付叶轮，减压盖，轴套均采用耐磨材料制造，维修量少，使用寿命长，使整机平均无故障工作时间MTBF大大提高。

Polyphenylene Sulfide as a heat-resistant, corrosion resistance, high rigidity material, and instrumentation can be the production of gears, axle sleeve; in the electrical industry, for the skeleton, bearing, terminal, etc.; in the chemical equipment, shell can be made pump, impeller, valves, etc.; in the automotive industry, for axial transverse rod bushing, fuel system components.

聚苯硫醚作为耐热、耐蚀、高刚性材料，在仪器仪表中，可制作齿轮、轴套；在电器工业中，作骨架、支座、接线柱等；在化工设备方面，可制作泵壳、叶轮、阀门等；在汽车工业，作轴向横拉杆衬套、燃料油系统部件等。

Stock and pintle are made of forged steel with stainless steel sleeves and synthetic bushes.

舵杆采用碶型连接，液压推入的安装方法。舵杆与舵栓材料为煅造件，轴套为不锈钢与人工合成材

A printing plate cylinder wear workparts, gap increased as a result of ink.

印版滚筒轴套磨损惨轻，间隙增不小而引起的不朱杠。

Especially in recent years for the development and production of the Korean company Hyosung GF series rocker arm bushings products and the success of products, Hyosung Corporation has been designated as China's only a few manufacturers of sentinel procurement cooperation.

特别是近年来为韩国晓星公司开发生产GF等系列摇臂产品和轴套类产品的成功，已被晓星公司定为中国仅有的几家定点采购合作厂家之一。

Its main products cover all kinds of Nuts,Bushings,Sleeves, Bushings,Socket Liner and Seals as accessories for forging press,steel rolling,minging(crushers-cone\symons etc),power generation equipment and ships in addition to copper alloy castings needed in other sectors.

产品/Product：主要产品是为锻压设备、轧钢设备、矿山设备、发电设备、船舶设备配套生产各种螺母、衬瓦、轴套、碗形轴瓦、密封体等及其它行业机械设备所需的铜、铝合金铸件。

At present, the development of wear-resistant alloys, tin bronze service life is 1-3 times the price of tin bronze is only about 60%, can effectively substitute for tin bronze ZCuSn6Zn6Pb3, ZCuSn10P1 and so on, can produce worm wheel, sleeve, bushing, nut, slider and so on, the alloy has high strength, wear resistance, and the proportion of small, die-casting with excellent performance characteristics.

目前开发的耐磨合金，使用寿命是锡青铜的1-3倍，而价格仅是锡青铜的60%左右，能有效替代锡青铜ZCuSn6Zn6Pb3、ZCuSn10P1等，可制造蜗轮、轴套、轴瓦、螺母、滑块等，该合金具有强度高，耐磨性好、比重小、压铸性能优良的特性。

XS alloy produced by cylindrical roller bearings, spherical self-aligning bearings, sleeve, bushing, nut mill, slider, skateboards, board-driven, high-temperature wear-resistant linings and other products.

用XS合金制作的圆柱滚子轴承，球面调心轴承、轴套、轴瓦、轧机螺母、滑块、滑板、导向板、高温耐磨衬板等产品。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。