轴套

Delrin acetal plastic bushings are interposed between the aluminum pivots and two Stainless Steel surfaces on the rear top tube .

Delrin缩醛塑料轴套是插嘴之间的铝铰和两个不锈钢表面的后方上管。

Anti-pollution machinery (such as textiles, paper, pharmaceutical, food machinery) of the bearing sleeve

1防污染机械(如纺织、造纸、制药、食品机械)的轴承轴套

Because the use of swelling sets of connections can be even smaller size of a shaft and bushings.

因为使用胀紧套连接可以用更小尺寸的轴和轴套。

Self-lubricated bushing is very popular in western countries.

自动润滑轴套在西方国家很流行。

The automobile half-shaft busing with direct forged inner hole has high strength and long service life .

直接锻造出内孔的汽车半轴套管强度高，寿命长，锻造工艺复杂。

Where cables passing through non-water-tight decks and bulkheads or beams etc., shall be chosen on such position where the hull strength not shall be damaged. Suitable bushing or coaming with round edge shall be used for their protection.

在电缆没有经过无水密们甲板或者隔板，横梁选择位置位于甲板的力量没有任何的损害，相配的轴套和舱口栏板和侧缘边必须使用保护措施。

Carbon steel machined slide bearings, the oil groove can be produced according to the bearings' working condition if needed.

以优质低碳钢为基体精加工而成的适用于重载低速环境恶劣工作部位的边界润滑轴套，轴套工作表面可按照工况条件加工出各种形式的油槽以起到充分润滑的作用。

First of all, horizontal swing to solve big problems, re-allocation of a motor sleeve (with the bronze with stent hole so), so that the electrical sleeve just in bronze wall bracket can rotate, reducing the gap; further axial movement to solve the problem with the motor shaft with Hexagon Hexagon washer so thick 0.6mm.

首先解决横向摆动大的问题，重新配做一个电机轴套，使电机轴套在铸铜支架内壁刚好能转动，减小间隙；再解决轴向窜动问题，与内六角电机轴配做内六角垫圈，厚0.6mm。

At present, our products have developed to machinery sealing, carbon-graphite products, resin product normal temperature, high temperature, strong anticorrosive, metal products dipped antimony, dipped aluminum, dipped aluminum alloy, dipped Babbitt alloy, shaft sleeve, bearing, slipper block, piston ring for oil-free cylinder, orienting sleeve, carborundum ceramic seal ringrotary joint.

目前产品发展至机械密封，石墨密封环、碳石墨制品浸渍有树脂类、金属类（浸锑，浸铝，浸铝合金，浸巴氏合金）、轴套、轴忖、轴承、滑块、无油汽缸用活塞环、导向套。碳化硅陶瓷密封环、轴套、轴承、分瓣环、导向套。

At present, our products have developed to machinery sealing, carbon-graphite products, resin product (normal temperature, high temperature, strong anticorrosive), metal products (dipped antimony, dipped aluminum, dipped aluminum alloy, dipped Babbitt alloy), shaft sleeve, bearing, slipper block, piston ring for oil-free cylinder, orienting sleeve, carborundum ceramic seal ring and rotary joint.

目前产品发展至机械密封，石墨密封环、碳石墨制品浸渍有树脂类、金属类（浸锑，浸铝，浸铝合金，浸巴氏合金）、轴套、轴忖、轴承、滑块、无油汽缸用活塞环、导向套。碳化硅陶瓷密封环、轴套、轴承、分瓣环、导向套。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。