轴套

The new pivot: Like the rest of you I love the bushing system on the Sebenza.

新主轴：我喜欢Sebenza 的轴套系统，但既然有了Umnumzan我也对新轴套系统的优点和缺点进行了思考。

Impeller with static balance is fixed onto the shaft by the sleeve and the sleeve nuts on the two sides. Its axial position may be adjusted through sleeve nut.

经过静平衡校验的叶轮，用轴套和两边的轴套螺母固定在轴上，其轴向位置可通过轴套螺母进行调整。

Pump rotor consists of first and second stage impeller, shaft sleeve, lock bolt, spacer sleeve, sleeve coupling , shaft-sleeve nut, pump coupling and main shaft.

泵的转子部件由首级叶轮、次级叶轮、轴套、锁紧螺栓、间隔套、挡套、套筒联轴器、轴套螺母、泵联轴器、主轴等组成。

The composition of the device comprises a substrate and a cover plate. A cross-form groove is disposed on the base material of the substrate; a disperse phase fluid inlet pipe and a fluid outlet pipe are respectively inlaid in the groove to form a coaxial sleeve structure; a continuous phase fluid inlet pipe is embedded in a groove on the two sides and connected with the coaxial sleeve; and the cover plate is hermitically attached to the upper surface of the substrate and seals the groove.

其组成包括基片和盖片：所述基片的基材上开有一个十字型凹槽；分散相流体入口管和流体出口管分别嵌入到凹槽内形成同轴套管结构；连续相流体入口管嵌入到两侧的凹槽内与所述同轴套管相连；所述盖片紧密贴合在所述基片的上表面上将所述凹槽进行密封。

Nano-imprint lithography drum paper teeth axis, swayig begnawing workparts paper teeth or wear, allows unleashmy begnawing paper teeth in paper in an inconsistent state in that result in bilateral irregular longitudinal misregister, in which case on slow computers are more likely to occur, because the impact of low-speed machine tipping bucket, the strength of a rotational motion paper teeth ranges of swayig high speed machine is used, and indirect sheet transfer unleashmy simpleplan paper teeth have smaller, at the same time as a result of automatic circulation lubrication oil system, unleashmy and apparatdus paper teeth axis is not easy to wear, but bearing in mind that oil, oilway jam torn oil grinding.

压印滚筒咬纸牙轴，摆动咬纸牙轴或轴套磨损后，不离使得咬纸牙在咬纸功程洋处于不稳不退状况，以至于爆发双边无次序的纵向套印禁绝，这栽环境在不低速机上比辛便当呈现，因为不低速机翻斗撞击辛不小，咬纸牙轴动弹幅度比辛不小，不低速机是拔取摆动不直接递纸，并且咬纸牙闭合幅度也较小，同时又由于有被迫轮回油路编制润滑，所以咬纸牙轴及轴套不便当磨损，但给夺目油眼，油路畅通导致不续油咬不松。

Aiming at the two structural features of axle shaft sleeve on the basis of analyzing various forming technologies applied in domestic and overseas in recent years,two new hot extrusion forming technology of axle shaft sleeve are worked out.

针对半轴套管的两种结构特点，在分析了国内外近年来所采用的各种成形工艺的基础上，分别开发了用镦粗-反挤压和扩径-正挤压两道复合工序相结合成形分体式半轴套管和用两次复合镦挤的方法成形整体式半轴套管的两种热挤压成形新工艺，通过物理模拟实验证明了成形工艺的可行性、实用性。

By chosing the material of axle sleeve with high strength and decreasing the length of contact face for axle sleeve and axle neck, the lubrication condition of frictional pairs was improved, and the wear was decreased.

结果表明，通过选用强度优异的轴套作为摩擦副，缩减沟槽尺寸以增加轴套与轴颈的接触面长度，改善了摩擦副的润滑状况，减少了磨损，满足了生产需要。

Tile cutting disks, deep drawing tools, plain bearings, sealing and sliding sealing rings, guide gibs, liners and bushings, shaft protective sleeves, rolls for cold rolling mills, tools for diecasting pulverized materials

饰面花砖切削盘、深拉工具、滑动轴承、密封圈和滑动密封圈、导向槽、衬垫和轴套、曲柄轴套、冷压磨碎机轧辊、硬模铸造研磨材料的工具、刀盘。

Tile cutting disks, deep drawing tools, plain bearings, sealing and sliding sealing rings, guide gibs, liners and bushings, shaft protective sleeves, rolls for cold rolling mills, tools for diecasting pulverized materials, cutting disks.

饰面花砖切削盘、深拉工具、滑动轴承、密封圈和滑动密封圈、导向槽、衬垫和轴套、曲柄轴套、冷压磨碎机轧辊、硬模铸造研磨材料的工具、刀盘。

Equably distributed oil socket secure the bushing,s load capacity , so the bushing is more durable

内孔均布的油穴不破坏轴套内壁的承载能力，延长了轴套的使用寿命

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。