轴壳

Stability of axially crushing shell was taken into account.

本文考虑了圆柱壳受轴向压缩载荷作用稳定性问题。

A slotted concentric cylinder carries a continuous solid wing across and in contact with the interior surface of an ovoid shell, shaped for exact diameter in all directions on the eccentric axis of revolution.

" "开槽同心圆柱体，带有连续固相荣跨越和联系，与内部表面一卵形壳，形状为直径的确切在各个方向上偏心轴的革命。

ABSTRACT :Automobile Clutch in the engine and gearbox between the flywheel shell, with screw will be fixed in the clutch assembly after the plane of the flywheel, clutch gearbox output shaft is the input shaft.

摘 要：汽车离合器位于发动机和变速箱之间的飞轮壳内，用螺钉将离合器总成固定在飞轮的后平面上，离合器的输出轴就是变速箱的输入轴。

ABSTRACT :Automobile Clutch in the engine and gearbox between the flywheel shell, with screw will be fixed in the clutch assembly after the plane of the flywheel, clutch gearbox output shaft is the input shaft.

摘要摘 要：汽车离合器位于发动机和变速箱之间的飞轮壳内，用螺钉将离合器总成固定在飞轮的后平面上，离合器的输出轴就是变速箱的输入轴。

Automobile Clutch in the engine and gearbox between the flywheel shell, with screw will be fixed in the clutch assembly after the plane of the flywheel, clutch gearbox output shaft is the input shaft.

摘要汽车离合器位于发动机和变速箱之间的飞轮壳内，用螺钉将离合器总成固定在飞轮的后平面上，离合器的输出轴就是变速箱的输入轴。

The pump rotor shaft and motor are installed vertically, pump inlet at the top of the lower part of the exhaust port at the pump, pump casing with a water-cooled units, to reduce the pump bearings and seal at the temperature.

泵的转子轴及电机均为竖直安装，泵进气口在上面，排气口在泵下部，泵壳带有水冷套，以降低泵轴承及轴封处的温度。

Along the axis within 2 cm, a hollow gas shell structure is formed.

估算结果为：在轴向2.5~40 mm，径向0~15 mm的区域内，气体分子密度基本在10^16~10^17/立方公分，且在轴向2 cm内基本形成空心的气体壳层结构。

Impeller installed in the pump shell 2, and fastening on the shaft 3, shaft driven by the motor directly.

叶轮安装在泵壳2内，并紧固在泵轴3上，泵轴由电机直接带动。

Impeller installed in the pump shell 2, and fastening on the shaft 3, shaft driven by the motor directly.

叶轮装置在泵壳2内，并松固在泵轴3上，泵轴由电机间接带动。

An isolating plate matching with the rotor in sliding way is arranged in the shell. An isolating plate sliding hole is opened on the shell wall between the closer inlet hole and the outlet hole. A sealing member is arranged in the isolating plate sliding hole.

其特征是在带有中心轴孔和进、出孔的壳体内通过中心轴设有侧面呈斜面的圆形转子，并设有与转子滑配的隔板，在两个相近的进、出孔间的壳壁上开有隔板滑孔，在隔板滑孔内设有密封件。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了